12 Non Access Stratum (NAS) Configuration parameter handling
31.1213GPPRelease 16TSUICC-terminal interfaceUniversal Subscriber Identity Module (USIM) application test specification
12.1 EFNASCONFIG – NAS signaling priority handling
12.1.1 Definition and applicability
If the UE is configured for NAS signalling priority (see 3GPP TS 24.368 [36], 3GPP TS 31.102 [4]), the UE shall indicate this by including the Device properties IE in the appropriate NAS message and setting the low priority indicator to "MS is configured to NAS signalling low priority". This NAS signalling low priority indication can be used by the network for NAS level mobility management congestion control on a per core network node basis and APN based congestion control.
The test case is covered in TS 34.123-1 [38] clauses 9.4.3.7, 9.4.5.5, 11.1.1.3, 11.1.1.4, 11.1.3.4, 11.2.2.3, 12.4.1.1e and 12.4.3.2a. Refer to CR #0229 for details.
12.1.2 Void
12.1.3 Void
12.1.4 Void
12.1.5 Void
12.2 EFNASCONFIG – NMO I Network Mode of Operation I handling
12.2.1 Definition and applicability
The behaviour of the UE with respect to NMO I is determined by the combination of PS domain specific system information IE and the setting of the parameter "NMO_I_Behaviour" in the NAS configuration Management Object as specified in 3GPP TS 24.368 [36] or in USIM file NASCONFIG as specified in 3GPP TS 31.102 [4].
The test case is covered in TS 34.123-1 [38] clause 12.2.2.3a. Refer to CR #0230 for details.
12.2.2 Void
12.2.3 Void
12.2.4 Void
12.2.5 Void
12.3 EFNASCONFIG – Attach with IMSI handling
12.3.1 Definition and applicability
The AttachWithIMSI leaf indicates whether attach with IMSI is performed when moving to a non-equivalent PLMN as specified in 3GPP TS 24.008 [16] and 3GPP TS 24.301 [26].
The test case is covered in TS 34.123-1 [38] clause 12.2.1.1a. Refer to CR #0224 for details.
12.3.2 Void
12.3.3 Void
12.3.4 Void
12.3.5 Void
12.4 EFNASCONFIG – Verifying Minimum Periodic Search Timer
12.4.1 Definition and applicability
The MinimumPeriodicSearchTimer leaf gives a minimum value in minutes for the timer T controlling the periodic search for higher prioritized PLMNs as specified in 3GPP TS 23.122 [31].
If the MS is configured for Fast First Higher Priority PLMN search and the MinimumPeriodicSearchTimer is configured as specified in 3GPP TS 24.368 [36] or 3GPP TS 31.102 [4], the MS shall not use a value for T that is less than the MinimumPeriodicSearchTimer.
The test case is covered in TS 34.123-1 [38] clauses 9.4.5.4 and 9.4.5.4.7. Refer to CR #0228 for details.
12.4.2 Void
12.4.3 Void
12.4.4 Void
12.4.5 Void
12.5 EFNASCONFIG – Extended access barring handling
12.5.1 Definition and applicability
Extended Access Barring (EAB) is a mechanism to control Mobile Originating access attempts from UEs that are configures for EAB in order to prevent overload for the access network and/or the core network. In congestion situations, the operator can restrict access from UEs configured for EAB while permitting access from other UEs.
The ExtendedAccessBarring leaf indicates whether the extended access barring is applicable for the UE as specified in 3GPP TS 24.008 [16] and 3GPP TS 24.301 [26].
The test case is covered in TS 34.123-1 [38] clauses 8.1.1.20, 9.4.11, 12.2.1.16 and 12.4.1.9. Refer to CR #0226 for details.
12.5.2 Void
12.5.3 Void
12.5.4 Void
12.5.5 Void
12.6 EFNASCONFIG – Verifying Timer T3245 Behaviour
12.6.1 Definition and applicability
For an MS that is configured to use timer T3245 (see 3GPP TS 24.368 [36] or 3GPP TS 31.102 [4]) and when the MS adds a PLMN identity to the "forbidden PLMN list" or the "forbidden PLMNs for GPRS service" list or sets the SIM/USIM as invalid for non-GPRS services or GPRS services or both, and timer T3245 is not running, the MS shall start timer T3245 with a random value, uniformly drawn from the range between 12h and 24h.
Upon expiry of the timer T3245, the MS shall erase the "forbidden PLMN list" and the "forbidden PLMNs for GPRS service" list and set the SIM/USIM to valid for non-GPRS services and GPRS services.
12.6.2 Conformance requirement
For NAS configuration parameter by USIM, the UE shall check and apply the setting present in EFNASCONFIG for "Timer T3245 Behaviour".
Reference:
– TS 31.102 [4], clauses 4.2.94, 5.2.29
– TS 24.368 [36], clause 5.7.
– TS 24.008 [16], clause 4.1.1.6
12.6.3 Test purpose
1) To verify that the UE reads the NAS configuration stored on the USIM.
2) To verify that the UE applies the USIM stored NAS configuration correctly to connect to the USS.
3) To verify that the UE erase the "forbidden PLMN list" and the "forbidden PLMNs for GPRS service" list upon expiry of the timer T3245.
12.6.4 Method of test
12.6.4.1 Initial conditions
a) The USS transmits on the BCCH, with the following network parameters:
– Attach/detach: disabled.
– LAI (MCC/MNC/LAC): 234/005/0001.
– RAI (MCC/MNC/LAC/RAC): 234/005/0001/05
– Access control: unrestricted.
b) The default Non Access Stratum Configuration UICC is installed into the Terminal with the following exception:
EFFPLMN (Forbidden PLMNs)
Logically: PLMN1: empty
PLMN2: empty
PLMN3: empty
PLMN4: empty
PLMN5: empty
PLMN6: empty
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
B12 |
|
Hex |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
|
Coding: |
B13 |
B14 |
B15 |
B16 |
B17 |
B18 |
||||||
|
Hex |
FF |
FF |
FF |
FF |
FF |
FF |
EFNASCONFIG (Non Access Stratum Configuration):
Logically:
NAS signalling priority value: Reserved (NAS signalling low priority is not used)
NMO I Behaviour value: "NMO I, Network Mode of Operation I" indication is not used
Attach with IMSI value: attach with IMSI is performed when moving to a non-equivalent PLMN
Minimum Periodic Search Timer value: 00
Extended access barring value: extended access barring is not applied for the UE
Timer T3245 Behaviour value: T3245 is used
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
80 |
01 |
00 |
81 |
00 |
00 |
82 |
01 |
00 |
83 |
01 |
|
Coding: |
B12 |
B13 |
B14 |
B15 |
B16 |
B17 |
B18 |
||||
|
Hex |
00 |
84 |
01 |
00 |
85 |
01 |
01 |
12.6.4.2 Procedure
a) The UE is powered on.
b) Depending on which domain the UE is going to be registered on, the UE attempts to perform CS, PS or CS/PS registration to the USS.
c) After receipt of a LOCATION UPDATING REJECT and/or ATTACH REJECT message during registration with the cause "PLMN not allowed" the Terminal shall update the EF FPLMN in the USIM. T3245 will start.
d) After the expiry of timer T3245, the terminal shall establish the RRC connection again.
e) Depending on which domain the UE is going to be registered on, the UE performs CS, PS or CS/PS registration to the USS.
f) The UE is powered down.
12.6.5 Acceptance criteria
a) After power on in step a) the UE shall reads EFNASCONFIG
b) The UE shall update EFFPLMN in step c) as following:
EFFPLMN (Forbidden PLMNs)
Logically: PLMN1: 234 005 (MCC MNC)
PLMN2: empty
PLMN3: empty
PLMN4: empty
PLMN5: empty
PLMN6: empty
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
B12 |
|
Hex |
32 |
54 |
00 |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
|
Coding: |
B13 |
B14 |
B15 |
B16 |
B17 |
B18 |
||||||
|
Hex |
FF |
FF |
FF |
FF |
FF |
FF |
c) The UE shall update EFFPLMN in step e) as following:
EFFPLMN (Forbidden PLMNs)
Logically: PLMN1: empty
PLMN2: empty
PLMN3: empty
PLMN4: empty
PLMN5: empty
PLMN6: empty
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
B12 |
|
Hex |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
FF |
|
Coding: |
B13 |
B14 |
B15 |
B16 |
B17 |
B18 |
||||||
|
Hex |
FF |
FF |
FF |
FF |
FF |
FF |
12.7 EFNASCONFIG – Override NAS signalling low priority
12.7.1 Definition and applicability
The "Override NAS signalling low priority" indicates whether the UE can override the NAS Signalling Priority configuration in the NAS message as specified in 3GPP TS 24.008 [16] and 3GPP TS 24.301 [26].
12.7.2 Conformance requirement
For NAS configuration parameter by USIM, the UE shall check and apply correctly the setting present in EFNASCONFIG for "Override NAS signalling low priority" to connect to the network.
References:
– TS 31.102 [4], clauses 4.2.94, 5.2.29
– TS 24.368 [36], clause 5.9.
– TS 24.008 [16], clause 1.8, 6.1.3.1.3.2, 6.1.3.12, 4.7.13.5
– TS 23.060 [25], clause 5.3.13.6.
12.7.3 Test purpose
1) To verify that the UE reads the NAS configuration stored on the USIM.
2) To verify that the UE applies the USIM stored NAS configuration correctly to connect to the USS.
12.7.4 Method of test
12.7.4.1 Initial conditions
a) The USS transmits on the BCCH, with the following network parameters:
– Attach/detach: disabled.
– LAI (MCC/MNC/LAC): 246/081/0001.
– RAI (MCC/MNC/LAC/RAC): 246/081/0001/05.
– Access control: unrestricted.
b) The default Non Access Stratum Configuration UICC is installed into the Terminal with the following exception:
EFNASCONFIG (Non Access Stratum Configuration)
Logically:
NAS signalling priority value: NAS signalling low priority
NMO I Behaviour value: "NMO I, Network Mode of Operation I" indication is not used
Attach with IMSI value: normal behaviour is applied
Minimum Periodic Search Timer value: 00
Extended access barring value: extended access barring is applied for the UE
Timer T3245 Behaviour value: T3245 not used
Override NAS signalling low priority: Indicates that the UE can override the NAS signalling low priority indicator
Override Extended access barring: Indicates that the UE can override extended access barring
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
80 |
01 |
01 |
81 |
01 |
00 |
82 |
01 |
00 |
83 |
01 |
|
Coding: |
B12 |
B13 |
B14 |
B15 |
B16 |
B17 |
B18 |
B19 |
B20 |
B21 |
B22 |
|
Hex |
00 |
84 |
01 |
01 |
85 |
01 |
00 |
86 |
01 |
01 |
87 |
|
Coding: |
B23 |
B24 |
|||||||||
|
Hex |
01 |
01 |
12.7.4.2 Procedure
a) The UE is powered on where the UICC is configured as defined in b) in the initial conditions.
b) The user requests activation of a PDP context. After receipt of ACTIVATE PDP CONTEXT REQUEST from the UE, the USS sends ACTIVATE PDP CONTEXT REJECT to the UE indicating:
– SM cause value # 26: insufficient resources;
– Back-off timer T3396: 1 minute
c) Before timer T3396 expires, the users request activation of a PDP context, the UE sends ACTIVATE PDP CONTEXT REQUEST, the USS sends ACTIVATE PDP CONTEXT ACCEPT to the UE.
d) The UE is powered down.
12.7.5 Acceptance criteria
a) After power on in step a) the UE shall read EFNASCONFIG
b) In step b) the UE shall set in ACTIVATE PDP CONTEXT REQUEST message the low priority indicator to "MS is configured for NAS signalling low priority" in the device properties.
c) In step c) the UE shall send ACTIVATE PDP CONTEXT REQUEST message where the low priority indicator is set to "MS is not configured for NAS signalling low priority" in the device properties.
12.8 EFNASCONFIG – Override Extended access barring
12.8.1 Definition and applicability
The "Override Extended Access Barring" indicates whether the UE can override "Extended Access Barring" configured to extended access barring.
The handling of extended access barring for the UE when the Override Extended Access Barring is used is specified in 3GPP TS 24.008 [16] and 3GPP TS 24.301 [26].
12.8.2 Conformance requirement
For NAS configuration parameter by USIM, the UE shall check and apply correctly the setting present in EFNASCONFIG for "Override Extended Access Barring" to connect to the network.
References:
– TS 31.102 [4], clauses 4.2.94, 5.2.29
– TS 24.368 [36], clause 5.10.
– TS 23.060 [25], clause 5.3.13.6.
– TS 23.401 [37], clause 4.3.17.2, 4.3.17.4
– TS 22.011 [6], clause 4.3.4.1.
12.8.3 Test purpose
1) To verify that the UE reads the NAS configuration stored on the USIM.
2) To verify that the UE applies the USIM stored NAS configuration correctly to connect to the USS.
3) To verify that the UE overrides "Extended Access Barring" when the Override Extended Access Barring is used
12.8.4 Method of test
12.8.4.1 Initial conditions
a) The USS transmits on the BCCH, with the following network parameters:
– Attach/detach: disabled.
– LAI (MCC/MNC/LAC): 246/081/0001.
– RAI (MCC/MNC/LAC/RAC): 246/081/0001/05.
– Access control: unrestricted.
– SYSTEM INFORMATION BLOCK TYPE 21:
EAB Authorization Mask: 0010000000 (Mobile stations configured for EAB and a member of Access Class 7 are barred)
EAB Subcategory (2 bit): 00 (The EAB Authorization mask is applicable to all mobile stations configured for EAB.)
b) The default Non Access Stratum Configuration UICC is installed into the Terminal with the following exception:
EFNASCONFIG (Non Access Stratum Configuration)
Logically:
NAS signalling priority value: Reserved (NAS signalling low priority is not used)
NMO I Behaviour value: "NMO I, Network Mode of Operation I" indication is not used
Attach with IMSI value: normal behaviour is applied
Minimum Periodic Search Timer value: 00
Extended access barring value: extended access barring is applied for the UE
Timer T3245 Behaviour value: T3245 not used
Override NAS signalling low priority: Indicates that the UE can override the NAS signalling low priority indicator
Override Extended access barring: Indicates that the UE can override extended access barring
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
80 |
01 |
00 |
81 |
01 |
00 |
82 |
01 |
00 |
83 |
01 |
|
Coding: |
B12 |
B13 |
B14 |
B15 |
B16 |
B17 |
B18 |
B19 |
B20 |
B21 |
B22 |
|
Hex |
00 |
84 |
01 |
01 |
85 |
01 |
00 |
86 |
01 |
01 |
87 |
|
Coding: |
B23 |
B24 |
|||||||||
|
Hex |
01 |
01 |
12.8.4.2 Procedure
a) The UE shall be powered on where the UICC is configured as defined in b) in the initial conditions and the USS transmits of the BCCH as defined inside the initial conditions.
b) User request activate a PDP context. The UE sends ACTIVATE PDP CONTEXT REQUEST, the USS sends ACTIVATE PDP CONTEXT ACCEPT to the UE.
c) The UE is powered down
12.8.5 Acceptance criteria
a) After power on in step a) the UE shall reads EFNASCONFIG
b) In step b) the UE shall send ACTIVATE PDP CONTEXT REQUEST message to the USS.
12.9 EFNASCONFIG – Fast First Higher Priority PLMN Search
12.9.1 Definition and applicability
The "Fast First Higher Priority PLMN Search" indicates whether the UE performs the first search for a higher priority PLMN after at least 2 minutes and at most T minutes upon entering a VPLMN as specified in 3GPP TS 23.122 [31].
12.9.2 Conformance requirement
For NAS configuration parameter by USIM, the UE shall check and apply correctly the setting present in EFNASCONFIG for "Fast First Higher Priority PLMN Search" to connect to the network.
References:
– TS 31.102 [4], clauses 4.2.94, 5.2.29
– TS 24.368 [36], clause 5.10a.
– TS 23.122 [31], clause 4.4.3.3.1
12.9.3 Test purpose
1) To verify that the UE reads the NAS configuration stored on the USIM.
2) To verify that the UE applies the USIM stored NAS configuration correctly to connect to the USS.
3) To verify that the UE performs first search for higher priority PLMN according to "Fast First Higher Priority PLMN Search" configuration when this parameter is present and used.
12.9.4 Method of test
12.9.4.1 Initial conditions
a) The USS transmits on BCCH, with the following network parameters:
– Attach/detach: disabled.
– LAI (MCC/MNC/LAC): 244/009/0001.
– RAI (MCC/MNC/LAC/RAC): 244/009/0001/05
– Access control: unrestricted.
b) After the registration of UE the USS transmits on a second BCCH, with the following network parameters:
– Attach/detach: disabled.
– LAI (MCC/MNC/LAC): 244/081/0001.
– RAI (MCC/MNC/LAC/RAC): 244/081/0001/05
– Access control: unrestricted.
c) The default Non Access Stratum Configuration UICC is installed into the Terminal with the following exception:
EFHPPLMN (Higher Priority PLMN Search period)
Logically: set to 6 minutes
|
Coding: |
B1 |
|
Hex |
01 |
EFNASCONFIG (Non Access Stratum Configuration)
Logically:
NAS signalling priority value: Reserved (NAS signalling low priority is not used)
NMO I Behaviour value: "NMO I, Network Mode of Operation I" indication is not used
Attach with IMSI value: normal behaviour is applied
Minimum Periodic Search Timer value: 00
Extended access barring value: extended access barring is not applied for the UE
Timer T3245 Behaviour value: T3245 not used
Override NAS signalling low priority: Indicates that the UE cannot override the NAS signalling low priority indicator
Override Extended access barring: Indicates that the UE cannot override extended access barring
Fast First Higher Priority PLMN Search: Indicates that the Fast First Higher Priority PLMN Search is enabled
EUTRA Disabling Allowed For EMM
Cause15: disabled
SM_RetryWaitTime: E0
SM_RetryAtRATChange: UE is allowed to retry the corresponding ESM procedure in S1 mode if an SM procedure was rejected in A/Gb or Iu mode, and to retry the corresponding SM procedure in A/Gb or Iu mode if an ESM procedure was rejected in S1 mode.
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
80 |
01 |
00 |
81 |
01 |
00 |
82 |
01 |
00 |
83 |
01 |
|
Coding: |
B12 |
B13 |
B14 |
B15 |
B16 |
B17 |
B18 |
B19 |
B20 |
B21 |
B22 |
|
Hex |
00 |
84 |
01 |
00 |
85 |
01 |
00 |
86 |
01 |
00 |
87 |
|
Coding: |
B23 |
B24 |
B25 |
B26 |
B27 |
B28 |
B29 |
B30 |
B31 |
B32 |
B33 |
|
Hex |
01 |
00 |
88 |
01 |
01 |
89 |
01 |
00 |
8A |
01 |
E0 |
|
Coding: |
B34 |
B35 |
B36 |
||||||||
|
Hex |
8B |
01 |
00 |
12.9.4.2 Procedure
a) The UE shall be powered on where the UICC is configured as defined in b) in the initial conditions and the USS starts to transmit on the first BCCH with the MMC/MNC 246/009.
b) Depending on which domain the UE is going to be registered on, the UE performs CS, PS or CS/PS registration to the USS.
c) The USS starts to send on the second BCCH with the MCC/MNC 244/081.
d) Depending on which domain the UE is going to be registered on, the UE performs CS, PS or CS/PS registration to the USS on the cell related to the BCCH transmitting MCC/MNC 244/081.
e) The UE is powered down.
12.9.5 Acceptance criteria
a) After power on in step a) the UE shall read EFNASCONFIG
b) The UE shall perform step d) after 2 – 6 minutes.
12.10 EFNASCONFIG – E-UTRA Disabling Allowed for EMM cause #15
12.10.1 Definition and applicability
The "EUTRA Disabling Allowed For EMM Cause #15" indicates whether the UE is allowed to disable the E-UTRA capability when it receives the Extended EMM cause IE with value "E-UTRAN not allowed" as described in 3GPP TS 24.301 [26].
12.10.2 Conformance requirement
For NAS configuration parameter by USIM, the UE shall check and apply the setting present in EFNASCONFIG for "EUTRA Disabling Allowed For EMM Cause #15" to connect to the network.
References:
– TS 31.102 [4], clauses 4.2.94, 5.2.29
– TS 24.368 [36], clause 5.10b.
– TS 24.301 [26], clause 4.5, 5.5.1.2.5
12.10.3 Test purpose
1) To verify that the UE reads the NAS configuration stored on the USIM.
2) To verify that the UE applies the USIM stored NAS configuration correctly to connect to the USS
3) To verify that the UE shall disable the E-UTRA capability and search for a suitable cell in GERAN or UTRAN radio access technology upon ATTACH REJECT reception that include both EMM cause #15 "no suitable cells in tracking area" and an Extended EMM cause IE with value "E-UTRAN not allowed" if " EUTRA Disabling Allowed For EMM Cause #15" is present and enabled in the UE.
12.10.4 Method of test
12.10.4.1 Initial conditions
a) For this test both a UTRAN USS and an E-UTRAN E-USS is needed.
The E-USS transmits on the BCCH, with the following network parameters:
– TAI (MCC/MNC/TAC): 244/003/0001.
– Access control: unrestricted.
At step c) the E-USS transmits on the BCCH, with the following network parameters:
– TAI (MCC/MNC/TAC): 244/003/0002.
– Access control: unrestricted.
At step c) the USS transmits on BCCH, with the following network parameters:
– Attach/detach: disabled.
– LAI (MCC/MNC/LAC): 244/003/0003.
– Access control: unrestricted.
The UICC is installed into the Terminal and the UE is set to automatic PLMN selection mode.
b) The default Non Access Stratum Configuration of E-UTRAN/EPC UICC is installed into the Terminal with the following exception:
EFNASCONFIG (Non Access Stratum Configuration)
Logically:
NAS signalling priority value: Reserved (NAS signalling low priority is not used)
NMO I Behaviour value: "NMO I, Network Mode of Operation I" indication is not used
Attach with IMSI value: normal behaviour is applied
Minimum Periodic Search Timer value: 00
Extended access barring value: extended access barring is not applied for the UE
Timer T3245 Behaviour value: T3245 not used
Override NAS signalling low priority: Indicates that the UE cannot override the NAS signalling low priority indicator
Override Extended access barring: Indicates that the UE cannot override extended access barring
Fast First Higher Priority PLMN Search: Indicates that the Fast First Higher Priority PLMN Search is enabled
EUTRA Disabling Allowed For EMM
Cause15: enabled
SM_RetryWaitTime: E0
SM_RetryAtRATChange: UE is allowed to retry the corresponding ESM procedure in S1 mode if an SM procedure was rejected in A/Gb or Iu mode, and to retry the corresponding SM procedure in A/Gb or Iu mode if an ESM procedure was rejected in S1 mode.
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
80 |
01 |
00 |
81 |
01 |
00 |
82 |
01 |
00 |
83 |
01 |
|
Coding: |
B12 |
B13 |
B14 |
B15 |
B16 |
B17 |
B18 |
B19 |
B20 |
B21 |
B22 |
|
Hex |
00 |
84 |
01 |
00 |
85 |
01 |
00 |
86 |
01 |
00 |
87 |
|
Coding: |
B23 |
B24 |
B25 |
B26 |
B27 |
B28 |
B29 |
B30 |
B31 |
B32 |
B33 |
|
Hex |
01 |
00 |
88 |
01 |
00 |
89 |
01 |
01 |
8A |
01 |
E0 |
|
Coding: |
B34 |
B35 |
B36 |
||||||||
|
Hex |
8B |
01 |
00 |
12.10.4.2 Procedure
a) The UE shall be powered on where the UICC is configured as defined in b) in the initial conditions and the E-USS starts to send only on the BCCH with the MCC/MNC 244/003.
b) After receipt of AttachRequest from the UE, the E-USS sends Attach Reject message with:
– EMM cause set to #15: "No suitable cells in tracking area",
– Extended EMM cause IE: "E-UTRAN not allowed"
c) The E-USS starts to send on the BCCH with MCC/MNC 244/003 and the USS starts to send on the BCCH with MCC/MNC 244/003.
d) After receipt of an RRCConnectionRequest from the UE, the USS sends RRCConnectionSetup to the UE, followed by RRCConnectionSetupComplete sent by the UE to the USS.
e) The UE is powered down.
12.10.5 Acceptance criteria
a) After power on in step a) the UE shall read EFNASCONFIG
b) In step d) the UE shall send a RRCConnectionRequest on the UTRAN-cell related to the BCCH transmitting MCC/MNC 244/003 to the USS.
12.11 EFNASCONFIG – SM_RetryWaitTime
12.11.1 Definition and applicability
The "SM_RetryWaitTime" indicates a configured UE retry wait time value applicable when in HPLMN or EHPLMN (see 3GPP TS 23.122 [31]) for controlling the UE session management retry behaviour when prior session management request was rejected by the network with cause value #8, #27, #32, #33 as specified in 3GPP TS 24.008 [16] and 3GPP TS 24.301 [26].
SM_RetryWaitTime shall be coded in the same format as the value part of GPRS Timer 3 IE as specified in Table 10.5.163a/3GPP TS 24.008 [16] converted into a decimal value.
12.11.2 Conformance requirement
For NAS configuration parameter by USIM, the UE shall check and apply the setting present in EFNASCONFIG for "SM_RetryWaitTime" to connect to the network.
Reference:
– TS 31.102 [4], clauses 4.2.94, 5.2.29
– TS 24.368 [36], clause 5.10c.
– TS 24.008 [16], clauses 6.1.3.1.3.3, 10.5.7.4a.
12.11.3 Test purpose
1) To verify that the UE reads the NAS configuration stored on the USIM.
2) To verify that the UE applies the USIM stored NAS configuration correctly to connect to the USS.
3) To verify that the UE behaves as described in TS 24.008 [16] clause 6.1.3.1.3.3, using the default value of 12 minutes for the back-off timer when the SM Retry Timer value is not configured.
4) To verify that the UE behaves as described in TS 24.008 [16] clause 6.1.3.1.3.3, using the configured SM Retry Timer value as back-off timer value.
12.11.4 Method of test
12.11.4.1 Initial conditions
a) The USS transmits on BCCH, with the following network parameters:
– Attach/detach: disabled.
– LAI (MCC/MNC/LAC): 246/081/0001.
– RAI (MCC/MNC/LAC/RAC): 246/081/0001/05.
– Access control: unrestricted.
b) The default Non Access Stratum Configuration UICC is installed into the Terminal with the following exception:
EFNASCONFIG (Non Access Stratum Configuration)
Logically:
NAS signalling priority value: Reserved (NAS signalling low priority is not used)
NMO I Behaviour value: "NMO I, Network Mode of Operation I" indication is not used
Attach with IMSI value: normal behaviour is applied
Minimum Periodic Search Timer value: 00
Extended access barring value: extended access barring is not applied for the UE
Timer T3245 Behaviour value: T3245 not used
Override NAS signalling low priority: Indicates that the UE cannot override the NAS signalling low priority indicator
Override Extended access barring: Indicates that the UE cannot override extended access barring
Fast First Higher Priority PLMN Search: Indicates that the Fast First Higher Priority PLMN Search is not enabled
EUTRA Disabling Allowed For EMM
Cause15: disabled
SM_RetryWaitTime: 60 seconds
SM_RetryAtRATChange: UE is allowed to retry the corresponding ESM procedure in S1 mode if an SM procedure was rejected in A/Gb or Iu mode, and to retry the corresponding SM procedure in A/Gb or Iu mode if an ESM procedure was rejected in S1 mode.
|
Coding: |
B1 |
B2 |
B3 |
B4 |
B5 |
B6 |
B7 |
B8 |
B9 |
B10 |
B11 |
|
Hex |
80 |
01 |
00 |
81 |
01 |
00 |
82 |
01 |
00 |
83 |
01 |
|
Coding: |
B12 |
B13 |
B14 |
B15 |
B16 |
B17 |
B18 |
B19 |
B20 |
B21 |
B22 |
|
Hex |
00 |
84 |
01 |
00 |
85 |
01 |
00 |
86 |
01 |
00 |
87 |
|
Coding: |
B23 |
B24 |
B25 |
B26 |
B27 |
B28 |
B29 |
B30 |
B31 |
B32 |
B33 |
|
Hex |
01 |
00 |
88 |
01 |
00 |
89 |
01 |
00 |
8A |
01 |
7E |
|
Coding: |
B34 |
B35 |
B36 |
||||||||
|
Hex |
8B |
01 |
00 |
12.11.4.2 Procedure
a) The UE is powered on where the UICC is configured as defined in b) in the initial conditions.
b) User request activate a PDP context. After receipt of ACTIVATE PDP CONTEXT REQUEST from the UE, the USS sends ACTIVATE PDP CONTEXT REJECT to the UE indicating:
– SM cause value #8: operator determined barring;
c) User request activate a PDP context and the UE sends ACTIVATE PDP CONTEXT REQUEST, the USS sends ACTIVATE PDP CONTEXT ACCEPT to the UE.
d) The UE is powered down.
12.11.5 Acceptance criteria
a) After power on in step a) the UE shall read EFNASCONFIG
b) In step c) the UE shall send ACTIVATE PDP CONTEXT REQUEST message after the SM_RetryWaitTime of 1 minute has expired.
12.12 EFNASCONFIG – SM_RetryAtRATChange
12.12.1 Definition and applicability
The "SM_RetryAtRATChange" indicates the UE’s retry behaviour when in HPLMN or EHPLMN (see 3GPP TS 23.122 [31]) after inter-system change between S1 mode and A/Gb or Iu mode as specified in 3GPP TS 24.008 [16] and 3GPP TS 24.301 [26].
12.12.2 Conformance requirement
Editor’s note: this clause is for future study.
12.12.3 Test purpose
Editor’s note: this clause is for future study.
12.12.4 Method of test
Editor’s note: this clause is for future study.
12.12.5 Acceptance criteria
Editor’s note: this clause is for future study.