15 Mapping of BSSGP and RANAP causes
29.0603GPPGeneral Packet Radio Service (GPRS)GPRS Tunnelling Protocol (GTP) across the Gn and Gp interfaceRelease 17TS
Table 15.1 through Table 15.4 define a mapping of BSSGP and RANAP causes used in connection with inter-RAT PS Handover to avoid different mappings in different implementations.
The cause code mapping in the MME for the inter-RAT PS Handover procedures in Annex D of 3GPP TS 23.401 [47] is described in 3GPP TS 29.010 [48].
Inter-RAT PS Handover from GERAN to UTRAN:
Table 15.1: Cause value mapping from PS HANDOVER REQUIRED to RELOCATION REQUEST
48.018 |
25.413 |
PS HANDOVER REQUIRED |
RELOCATION REQUEST |
Uplink quality |
Time Critical Relocation |
Uplink strength |
Time Critical Relocation |
Downlink quality |
Time Critical Relocation |
Downlink strength |
Time Critical Relocation |
Distance |
Time Critical Relocation |
Better cell |
Relocation Desirable for Radio Reasons |
Traffic |
Resource Optimisation Relocation |
Cell traffic congestion |
Reduce Load in Serving Cell |
Any other value |
Relocation Desirable for Radio Reasons |
Table 15.2: Cause value mapping from RELOCATION FAILURE to PS HANDOVER NACK
25.413 |
48.018 |
RELOCATION FAILURE |
PS HANDOVER REQUIRED NACK |
No Radio Resources Available in Target Cell |
Cell traffic congestion |
Requested Ciphering and/or Integrity Protection algorithms not supported |
Requested ciphering and/or integrity protection algorithms not supported |
Incoming Relocation Not Supported Due To PUESBINE Feature |
Incoming relocation not supported due to PUESBINE feature |
Traffic Load In The Target Cell Higher Than In The Source Cell |
Cell traffic congestion |
O&M Intervention |
O&M intervention |
Any other value |
Relocation failure in target system |
Inter-RAT PS Handover from UTRAN to GERAN:
Table 15.3: Cause value mapping from RELOCATION REQUIRED to PS HANDOVER REQUEST
25.413 |
48.018 |
RELOCATION REQUIRED |
PS HANDOVER REQUEST |
Time Critical Relocation |
Time critical relocation |
Resource Optimisation Relocation |
Traffic |
Relocation Desirable for Radio Reasons |
Better cell |
Directed Retry |
Directed Retry |
Reduce load in Serving Cell |
Cell traffic congestion |
Any other value |
Better cell |
Table 15.4: Cause value mapping from PS HANDOVER NACK to RELOCATION PREPARATION FAILURE
48.018 |
25.413 |
PS HANDOVER REQUEST NACK |
RELOCATION PREPARATION FAILURE |
PFC create failure |
Relocation Failure in Target CN/RNC or Target System |
Cell traffic congestion |
No Radio Resources Available in Target Cell |
Equipment failure |
Relocation Failure in Target CN/RNC or Target System |
O&M intervention |
O&M Intervention |
Any other value |
Relocation Failure in Target CN/RNC or Target System |
Annex A (informative):
A method for sequence number checking
This annex describes a method to determine whether or not a received T-PDU is valid, for the Usage of the Sequence Number, clause 9.3.1.1.
This method deals with two distinct problems.
The first one is the "drifting" between the Sequence Number value that we expect to receive in the light of the total number of T-PDU received for this tunnel (the Expected value), and the effective received value. The probability that the received T-PDU is not correct because not awaited is higher if the distance between expected and received Sequence Numbers is high than if this distance is low. This leads to Condition 1. Its left part represents the distance between the Expected and received values, in a circular 65536 dimension.
The second one is the duplication of T-PDU frames within a given number of last received frames that have been accepted by the condition 1.
This leads to the following actions:
-This operation shall start when the dialogue is established between the GSNs. When each T-PDU is received during the dialogue, if this T-PDU is valid, its Sequence Number shall be saved. The last "A" saved Sequence Numbers represent the "Recorded Sequence Number Set".
A received T-PDU sequence number is valid only if it satisfies both of the following conditions:
1) Min(Abs(E – r), Abs(r – 65536 – E), Abs(E – 65536 – r)) < "B" Condition 1
Where: "E" is the Expected Sequence Number and "r" is the received Sequence Number.
2) The received Sequence Number is not a member of the Recorded Sequence Number Set. Condition 2.
"A" and "B" are parameters. The receiving GSN shall discard a received T-PDU with an invalid Sequence Number.
Abs(X) represents the absolute value of the number X.
Min(X,Y,Z) represents the lowest value taken from the numbers X, Y, and Z.
Annex B (Normative):
SGSN mapping table between Gn/Gp and NAS Cause values
The SGSN initiates session management requests towards the GGSN or mobility management requests towards the source/target SGSN. If these operations are not successful, there are several possible cause codes, which need to be mapped to appropriate cause codes over NAS to the UE.
Additionally, the SGSN initiates session management requests towards the UE. If this operation is not successful, there are several possible NAS cause codes which need to be mapped to appropriate GTP cause codes over Gn/Gp interface towards the GGSN.
The SGSN should map these cause codes as defined in tables B.1 to B.5 unless specified otherwise in the tables.
Table B.1: Mapping from Gn/Gp to NAS SM Cause values – Rejection indication from GGSN
Reject indication from GGSN to SGSN over Gn/Gp |
NAS SM Cause to UE (NOTE 1, NOTE 2, NOTE 3) |
#192 "Non-existent" |
#30 "Activation rejected by GGSN, Serving GW or PDN GW" #38 "Network failure" #43 "Unknown PDP Context" |
#193 "Invalid Message Format" |
#30 "Activation rejected by GGSN, Serving GW or PDN GW" #38 "Network failure" |
#194 "IMSI/IMEI not known" |
#30 "Activation rejected by GGSN, Serving GW or PDN GW" #38 "Network failure" #43 "Unknown PDP Context" |
#198 "Version not supported" |
#30 "Activation rejected by GGSN, Serving GW or PDN GW" #38 "Network failure" |
#199 "No Resources available" |
#34 "Service option temporarily out of order" #26 "Insufficient resources" |
#200 "Service not supported" |
#32 "Service option not supported" |
#201 "Mandatory IE incorrect" |
#30 "Activation rejected by GGSN, Serving GW or PDN GW" #38 "Network failure" |
#202 "Mandatory IE missing" |
#30 "Activation rejected by GGSN, Serving GW or PDN GW" #38 "Network failure" |
#203 "Optional IE incorrect" |
#30 "Activation rejected by GGSN, Serving GW or PDN GW" #38 "Network failure" |
#204 "System Failure" |
#34 "Service option temporarily out of order" #38 "Network failure" #30 "Activation rejected by GGSN, Serving GW or PDN GW" |
#209 "User authentication failure" |
#29 "User authentication failed" |
#210 "Context not found" |
#30 "Activation rejected by GGSN, Serving GW or PDN GW" #38 "Network failure" #43 "Unknown PDP Context" |
#211 "All dynamic PDP addresses are occupied" |
#26 "Insufficient resources" |
#212 "No memory is available" |
#34 "Service option temporarily out of order" #26 "Insufficient resources" |
#215 "Semantic error in the TFT operation" |
#41 "Semantic error in the TFT operation" |
#216 "Syntactic error in the TFT operation" |
#42 "Syntactical error in the TFT operation" |
#217 "Semantic errors in packet filter(s)" |
#44 "Semantic errors in packet filter(s)" |
#218 "Syntactic errors in packet filter(s)" |
#45 "Syntactical error in packet filter(s)" |
#219 "Missing or unknown APN" |
# 27 "Missing or unknown APN" |
#220 "Unknown PDP address of PDP type" |
#28 "Unknown PDP address or PDP type" |
#221 "PDP context without TFT already activated" |
#46 "PDP context without TFT already activated" |
#222 "APN access denied – no subscription" |
#33 "Requested service option not subscribed" # 27 "Missing or unknown APN" |
#223 "APN Restriction type Incompatible with currently active PDN connection" |
#112 "APN restriction value incompatible with active PDP context" |
#228 "Collision with network initiated request" |
#56 "Collision with network initiated request" |
#229 "APN Congestion" |
#26 "Insufficient resources" |
#230 "Bearer handling not supported" |
#60 "Bearer handling not supported" |
NOTE 1: See 3GPP TS 24.008 [5] for NAS SM causes. NOTE 2: The SGSN may for certain GTP cause codes trigger a new GTP procedure instead of rejecting the NAS request. NOTE 3: When multiple NAS Cause values are defined for a given GTP cause value, any of those NAS Cause values may be sent to the UE based on implementation choice. |
Table B.2: Mapping from Gn/Gp to NAS SM Cause values – Acceptance indication from GGSN
Acceptance indication from GGSN to SGSN over Gn/Gp |
NAS SM Cause to UE |
#129 "New PDP type due to network preference" |
#50 "PDP type IPv4 only allowed" #51 "PDP type IPv6 only allowed" (NOTE 1) |
#130 "New PDP type due to single address bearer only" |
#52 "single address bearers only allowed" |
NOTE 1: The actual NAS cause sent to the UE depends on the allocated IP address type. |
Table B.3: Mapping from Gn/Gp to NAS Cause values – Indication in request message from GGSN
Indication in a request message from GGSN to SGSN over Gn/Gp |
NAS SM Cause to UE |
#6 "Reactivation Requested" (NOTE 1) |
Shall be mapped to: #39 "Reactivation requested" in the NAS PDP context deactivation procedure. |
NOTE 1: In Delete PDP Context Request during the GGSN initiated PDP Context Deactivation Procedure with the Teardown indicator set. |
Table B.4: Mapping from NAS to Gn/Gp Cause values – Rejection indication from SGSN
NAS SM Cause from UE (NOTE 1) |
Reject indication from SGSN to GGSN over Gn/Gp (NOTE 2) |
#26 "Insufficient Resources" |
#199 "No Resources available" #197 "MS Refuses" |
#31 "Activation rejected, unspecified" |
Implementation specific cause value indicating that the MS has rejected the request without specifying any reason. |
#37 "QoS not accepted" |
Implementation specific cause value indicating that the MS has rejected the new QoS provided by the network as part of PDP Context Modification procedure. |
#40 "Feature not supported" |
#197 "MS Refuses" |
#41 "Semantic error in the TFT operation" |
#215 "Semantic error in the TFT operation" |
#42 "Syntactical error in the TFT operation" |
#216 "Syntactical error in the TFT operation" |
#43 "Unknown PDP Context" |
#210 "Context not found" #197 "MS Refuses" |
#44 "Semantic errors in packet filter(s)" |
#217 "Semantic errors in packet filter(s)" |
#45 "Syntactical error in packet filter(s)" |
#218 "Syntactical error in packet filter(s)" |
#46 "PDP context without TFT already activated" |
#221 "PDP context without TFT already activated" #197 "MS Refuses" |
#48 "Request rejected, Bearer Control Mode violation" |
#227 "Bearer Control Mode violation" #197 "MS Refuses" |
NOTE 1: See 3GPP TS 24.008 [5] for NAS SM causes respectively. NOTE 2: When multiple GTP Cause values are defined for a given NAS Cause value, any of those GTP Cause values may be sent to the GGSN based on implementation choice. |
Table B.5: Mapping from Gn/Gp to NAS Cause values – Rejection indication from SGSN
Reject indication from SGSN to SGSN over Gn/Gp |
NAS SM Cause to UE (NOTE 1, NOTE 2) |
#231 "Target access restricted for the subscriber" |
#15 "No suitable cells in tracking area", or #13 "Roaming not allowed in this tracking area", or #12 "Tracking area not allowed" |
NOTE 1: See 3GPP TS 24.008 [5] for NAS SM causes. NOTE 2: When multiple NAS Cause values are defined for a given GTP cause value, any of those NAS Cause values may be sent to the UE based on implementation choice. |
Annex C (informative):
Change history
Date |
TSG # |
TSG Doc. |
CR |
Rev |
Cat |
Subject/Comment |
New |
Apr 1999 |
Transferred to 3GPP CN1 |
||||||
CN#03 |
Approved at CN#03 |
3.0.0 |
|||||
001 |
Replacing the V(R) transfer mechanism with the N-PDU number transfer mechanism in routing area update |
||||||
CN#4 |
002 |
Clarification of ambiguous/superfluous information |
3.1.0 |
||||
003 |
Timer handling in GTP |
||||||
005 |
Mandatory SGSN Context Acknowledge message |
||||||
006 |
Mandatory info in MM Context IE |
||||||
007 |
APN to be transferred in the PDP context at inter SGSN RA update |
||||||
008 |
Consistency on implemented CRs from SMG#28 |
||||||
009 |
Removal of changes in PDP context establishment and restoration |
||||||
010 |
MSISDN in the Create PDP Context request |
||||||
CN#05 |
014r2 |
Specification of the MSISDN Information Element in GSM 09.60 |
3.2.0 |
||||
CN#06 |
017r4 |
QoS enhancements |
3.3.0 |
||||
CN#06 |
031 |
Merged CRs on GTP Enhancements |
3.3.0 |
||||
CN#07 |
033r2 |
Addition of Radio Priority to the SGSN Context Response |
3.4.0 |
||||
CN#07 |
035r2 |
Addition of Packet Flow Id to the SGSN Context Response |
3.4.0 |
||||
CN#07 |
036r1 |
Change the attribution of the PDP Context IE |
3.4.0 |
||||
CN#07 |
037 |
Add new cause value |
3.4.0 |
||||
CN#07 |
038 |
Addition of NSAPI to GGSN-initiated Update PDP Context |
3.4.0 |
||||
CN#07 |
040 |
Improving charging efficiency |
3.4.0 |
||||
CN#07 |
041r1 |
Subscriber and equipment trace for PS domain |
3.4.0 |
||||
CN#07 |
042 |
Necessity of the function of the calculation an SGSN IP address from the target ID |
3.4.0 |
||||
CN#07 |
045r1 |
Removal of Anonymous Access |
3.4.0 |
||||
CN#07 |
046r1 |
Clarification of Authentication Type and Import of Parameters |
3.4.0 |
||||
CN#07 |
048 |
Correction of IE types and order |
3.4.0 |
||||
CN#07 |
050r2 |
Clarification on Protocol Type in GTP Header |
3.4.0 |
||||
CN#07 |
051 |
Clarification of Repeated Information Element Ordering |
3.4.0 |
||||
CN#07 |
052r2 |
Method for GTP extension headers support |
3.4.0 |
||||
CN#07 |
053r2 |
The addition of the conditional description of the GTP parameters |
3.4.0 |
||||
CN#07 |
056 |
Change of naming when referring to primary and secondary contexts |
3.4.0 |
||||
CN#07 |
057 |
Removal of X.25 |
3.4.0 |
||||
CN#07 |
058r1 |
Use of 3 Digit MNCs in GTP for R’99 |
3.4.0 |
||||
CN#07 |
063r2 |
QoS Profile IE modification |
3.4.0 |
||||
CN#07 |
067r1 |
Distribution of security data |
3.4.0 |
||||
CN#07 |
069r1 |
New cause codes for TFT and packet filter errors |
3.4.0 |
||||
CN#07 |
070 |
IPv6 support as optional in Iu and Gn |
3.4.0 |
||||
CN#07 |
072r4 |
Clarification on the use of TEID in the GTP header |
3.4.0 |
||||
CN#07 |
073 |
Clarification to the function of the calculation of an SGSN IP address from the target ID |
3.4.0 |
||||
CN#07 |
075 |
Changing references from GSM specifications to 3GPP TS |
3.4.0 |
||||
CN#07 |
076 |
New table for Information Elements |
3.4.0 |
||||
CN#07 |
077 |
Forward SRSN Context |
3.4.0 |
||||
CN#07 |
078r1 |
PDCP sequence numbers in SRNC relocation and inter-system handover |
3.4.0 |
||||
CN#07 |
079 |
Removal of TCP support in the packet domain PLMN backbone network |
3.4.0 |
||||
CN#07 |
081 |
Addition of PDP Context Identifier to PDP Context Information Element |
3.4.0 |
||||
CN#07 |
083 |
Editorial clarification of information elements in the SGSN Context Response |
3.4.0 |
||||
CN#08 |
084 |
16-bit PDCP sequence numbers in GTP header |
3.5.0 |
||||
CN#08 |
085 |
Mandatory inclusion of IMSI in SGSN Context Response if P-TMSI Signature Mismatch |
3.5.0 |
||||
CN#08 |
086r1 |
Encoding of spare IMSI Digits |
3.5.0 |
||||
CN#08 |
087r1 |
Reliable delivery of signalling messages |
3.5.0 |
||||
CN#08 |
088 |
Possible cause codes for Relocation Cancel Response |
3.5.0 |
||||
CN#08 |
089 |
Condition for evaluating the sequence number fields in PDP context |
3.5.0 |
||||
CN#08 |
090r1 |
Target RNC Information |
3.5.0 |
||||
CN#08 |
091r1 |
Change of the length of TI |
3.5.0 |
||||
CN#08 |
092r1 |
Clean up for 29.060 |
3.5.0 |
||||
CN#08 |
093r2 |
Clarification on the TEID handling |
3.5.0 |
||||
CN#08 |
094r1 |
QoS Profile IE modification |
3.5.0 |
||||
CN#08 |
096 |
Restart counter in Echo response |
3.5.0 |
||||
CN#08 |
097r1 |
Clarification on the use of TEID in the GTP-C header |
3.5.0 |
||||
CN#08 |
098 |
Add APN IE for PDU Notification Reject Request message |
3.5.0 |
||||
CN#08 |
099r1 |
Addition of response code Delete PDP Context Response |
3.5.0 |
||||
CN#08 |
100r1 |
Introduction of a different port number for GTP-C and GTP-U |
3.5.0 |
||||
CN#08 |
101r1 |
Addition of charging characteristics per PDP context |
3.5.0 |
||||
CN#08 |
102 |
Alignment of text with tables |
3.5.0 |
||||
CN#08 |
106 |
Removal of Connection oriented paths |
3.5.0 |
||||
CN#08 |
108 |
On the use of the Sequence number in GTP-C |
3.5.0 |
||||
CN#08 |
109 |
N-PDU number in GTP-C |
3.5.0 |
||||
CN#08 |
110r1 |
Editorial modifications due to the upgrade from GTPv0 to GTPv1 for R´99 |
3.5.0 |
||||
CN#08 |
111r1 |
Editorial modifications concerning GTP-U and GTP-C |
3.5.0 |
||||
CN#08 |
112 |
Introducing Supported Extension Headers Notification to GTP-U |
3.5.0 |
||||
CN#08 |
113 |
Missing IEs in Error Indication |
3.5.0 |
||||
CN#08 |
114 |
Clarification of the Cause of Create PDP Context Response |
3.5.0 |
||||
CN#08 |
115 |
Clarification of the TEID for Signalling |
3.5.0 |
||||
CN#08 |
116 |
Clarification on the TEID for Signalling of the PDU Notification Reject Request |
3.5.0 |
||||
CN#08 |
117r2 |
Clarification of the conditional information elements |
3.5.0 |
||||
CN#08 |
119 |
Clarification on the use of SGSN address at PDU notification procedure (R99) |
3.5.0 |
||||
CN#09 |
105r1 |
Race Conditions Avoidance |
3.6.0 |
||||
CN#09 |
121 |
Definition of TEID value in GTP-U header |
3.6.0 |
||||
CN#09 |
122r3 |
Solution for race condition of GTP procedures |
3.6.0 |
||||
CN#09 |
123r1 |
Clarifications concerning the use of TEID in the Control Plane |
3.6.0 |
||||
CN#09 |
124r1 |
Editorial modifications concerning TEID Control Plane and TEID Data |
3.6.0 |
||||
CN#09 |
126r2 |
Sequence number in signalling messages |
3.6.0 |
||||
CN#09 |
127 |
Clarification of the conditional information elements |
3.6.0 |
||||
CN#09 |
128r1 |
Enhancement of MS Network capability and GPRS Ciphering Algorithm |
3.6.0 |
||||
CN#09 |
129 |
IPv6 support for Charging Gateway Address |
3.6.0 |
||||
CN#09 |
130 |
Signalling messages in GTP |
3.6.0 |
||||
CN#09 |
131r1 |
Security parameter transport in case of 2G-3G interworking |
3.6.0 |
||||
CN#09 |
132r1 |
Encoding of IMSI |
3.6.0 |
||||
CN#09 |
133 |
Removal of IHOSS from GTP |
3.6.0 |
||||
CN#09 |
135 |
Addition of MS Not Reachable Reason to Send Routing Information For GPRS Response |
3.6.0 |
||||
CN#09 |
138r1 |
Coding of TI in PDP Context |
3.6.0 |
||||
CN#09 |
139r1 |
Clarifications on the use of TEID in the Control Plane |
3.6.0 |
||||
CN#09 |
140 |
Correction on the handling of the PDP Context at unsuccessful PDP Context modification |
3.6.0 |
||||
CN#09 |
141r2 |
Categorize Error indication as the GTP-U message |
3.6.0 |
||||
CN#09 |
142 |
Clarifications on the presence condition of TLLI/P-TMSI in SGSN Context request |
3.6.0 |
||||
CN#09 |
143r2 |
Correction on Reliable transmission of signalling messages |
3.6.0 |
||||
CN#09 |
144 |
Alignment of the description of tables for Identification Request and SGSN Context Request |
3.6.0 |
||||
CN#09 |
145r1 |
Correction to the SGSN Context transfer Request and response messages |
3.6.0 |
||||
CN#09 |
146r2 |
Correction to the SGSN Forward relocation Request and Response messages |
3.6.0 |
||||
CN#09 |
147 |
Clarification or the handling of response messages |
3.6.0 |
||||
CN#09 |
148 |
Clarification on SGSN context acknowledge message |
3.6.0 |
||||
CN#10 |
136r2 |
Compatibility GTPv0/GTPv1 in case of SGSN change |
3.7.0 |
||||
CN#10 |
149 |
Clarification on the use of Teardown Indicator |
3.7.0 |
||||
CN#10 |
150 |
Correction to the PDU Notification Request message |
3.7.0 |
||||
CN#10 |
151r1 |
Correction of wrong entry in information table |
3.7.0 |
||||
CN#10 |
152 |
Moving of Annex A to 3GPP TS 23.003 |
3.7.0 |
||||
CN#10 |
153r2 |
Selecting GGSN IP address |
3.7.0 |
||||
CN#10 |
154r1 |
Removal of "Version not Supported" for GTP-U |
3.7.0 |
||||
CN#10 |
157 |
Correction of Security parameters length |
3.7.0 |
||||
CN#10 |
159 |
MS Network Capability in MM Context |
3.7.0 |
||||
CN#10 |
161 |
Clarifications to the usage of CKSN and KSI for security type 0 |
3.7.0 |
||||
CN#11 |
155r4 |
Adding Uplink TEID Data I and user plane GGSN address to PDP Context IE |
3.8.0 |
||||
CN#11 |
162 |
Handling of sequence numbers for reliable transmission of control plane messages |
3.8.0 |
||||
CN#11 |
163 |
Re-configure the IEs in the PDU Notification Request to make it in ascending order |
3.8.0 |
||||
CN#11 |
166 |
Corrections to editor work of 29.060 v 3.7.0 |
3.8.0 |
||||
CN#11 |
170r2 |
Clarification on the TEID value of the signalling messages |
3.8.0 |
||||
CN#11 |
173r3 |
Clarifications to the GTP-U protocol |
3.8.0 |
||||
CN#11 |
174r1 |
Essential Correction of the delete PDP context procedure |
3.8.0 |
||||
CN#11 |
178 |
Re-configure the IEs in the Send Routeing Information for GPRS Response message to make it in ascending order |
3.8.0 |
||||
CN#11 |
180r1 |
IMSI Encoding Clarification |
3.8.0 |
||||
CN#11 |
181r1 |
Fix an ambiguous description on the treatment for the PDP Type PPP in PDP context creation procedure |
3.8.0 |
||||
CN#11 |
182r2 |
GSN address in Error Indication |
3.8.0 |
||||
CN#11 |
186r1 |
Clarification of Error Indication |
3.8.0 |
||||
CN#11 |
187 |
Clarification on the handling of sequence numbers in the GTP user plane |
3.8.0 |
||||
CN#11 |
188 |
Clarifications and clean up of the error handling clause |
3.8.0 |
||||
CN#11 |
191r1 |
Clarification on the use of the term G-PDU |
3.8.0 |
||||
CN#11 |
Version increased from R99 to Rel-4 after CN#11. |
4.0.0 |
|||||
CN#12 |
194 |
Correction/Clarification of GGSN handling of Update PDP Context Response |
4.1.0 |
||||
CN#12 |
196 |
Correction due to incorrectly implemented CR on the Error indication message |
4.1.0 |
||||
CN#12 |
198 |
RNC IP Address IE format |
4.1.0 |
||||
CN#12 |
208 |
GTP Message Treatment |
4.1.0 |
||||
CN#12 |
220 |
Clarification of the handling of Version Not Supported; Supported Extension Headers and Error Indication messages |
4.1.0 |
||||
CN#12 |
221 |
Removal of the useless "version not supported" cause code from GTP messages |
4.1.0 |
||||
CN#12 |
222 |
Ambiguous text description of the Charging Gateway Address IE handling in the GTP create PDP context request message |
4.1.0 |
||||
CN#12 |
227 |
Alignment of the 29.060 with the 23.060 for the SRNS Relocation procedure |
4.1.0 |
||||
CN#13 |
Editorial clean up |
4.2.0 |
|||||
CN#13 |
230r1 |
Introduction of the Suspend-resume functionality in Rel-4 GTP specification |
4.2.0 |
||||
CN#13 |
236 |
Clarification of the term TLLI in SGSN Context Request |
4.2.0 |
||||
CN#13 |
238r1 |
Rewording usage of P-TIMSI and TLLI in "SGSN context request" |
4.2.0 |
||||
CN#13 |
240 |
Alignment with 23.060 on the use of SGSN Context Acknowledge message |
4.2.0 |
||||
CN#13 |
245r1 |
Charging Characteristics Inclusion in Create PDP Context Message |
4.2.0 |
||||
CN#13 |
247 |
Clarification to the usage of the TEID-C |
4.2.0 |
||||
CN#13 |
248r1 |
Clarification on the use of the teardown indicator IE |
4.2.0 |
||||
CN#14 |
255 |
Add APN.OI sub-field to the APN in PDP context IE |
4.3.0 |
||||
CN#14 |
264 |
Clarification of header marker setting for Error Indication |
4.3.0 |
||||
CN#14 |
268r1 |
GGSN address for control plane must not be changed in "Update PDP Context Response" |
4.3.0 |
||||
CN#14 |
273 |
Clarification on the handling of the GTP MM Context IE |
4.3.0 |
||||
CN#14 |
274 |
Clarification on the GTP PDP context IE |
4.3.0 |
||||
CN#14 |
283 |
Clarification on the handling of protocol configuration options IE |
4.3.0 |
||||
CN#14 |
259r1 |
Relay of Identification Request message and SGSN Context Request message |
5.0.0 |
||||
CN#14 |
272 |
Support for Radio Priority LCS |
5.0.0 |
||||
CN#14 |
282 |
Clarification on IMSI format (Unused fields) |
5.0.0 |
||||
Jan 2002 |
A coversheet fixed |
5.0.1 |
|||||
CN#15 |
291r1 |
Clarification on the use of the Teardown indicator IE |
5.1.0 |
||||
CN#15 |
294r1 |
Dangling PDP contexts handling |
5.1.0 |
||||
CN#15 |
297r1 |
Re-define the attributions of GTP Information Element |
5.1.0 |
||||
CN#15 |
299r1 |
Clarification on PDP address field and end user address information element in create PDP context response |
5.1.0 |
||||
CN#15 |
300r3 |
Generic RAN Information Procedure |
5.1.0 |
||||
CN#15 |
301 |
Priority of PDP Contexts at Inter-SGSN RA Update |
5.1.0 |
||||
CN#15 |
309r1 |
IMS Enhancements (PCO in Secondary PDP context activation procedures) |
5.1.0 |
||||
CN#16 |
311 |
Clarification on create PDP context for existing PDP context |
5.2.0 |
||||
CN#16 |
318 |
Support of IPv4 and IPv6 node addresses in Core Network |
5.2.0 |
||||
CN#16 |
319r2 |
Reference to 3GPP TS 33.210 for protection of GTP. |
5.2.0 |
||||
CN#17 |
322r1 |
Clarification re. response message |
5.3.0 |
||||
CN#17 |
323r2 |
Clarification re. Version Not Supported message |
5.3.0 |
||||
CN#17 |
324r1 |
Incorrect references |
5.3.0 |
||||
CN#17 |
325r2 |
RAB Setup Information for IPv6 |
5.3.0 |
||||
CN#17 |
328r2 |
Clarification on the coding of RANAP cause value |
5.3.0 |
||||
CN#17 |
329r1 |
Addition of PCO IE to Update PDP context procedures |
5.3.0 |
||||
CN#17 |
332r1 |
Setting PDP ID after inter-SGSN RAU using GTPv0 |
5.3.0 |
||||
CN#17 |
336 |
Removing inconsistency in definition of PDP Address length |
5.3.0 |
||||
CN#17 |
339 |
16 bit PDCP sequence numbers in RAB Context |
5.3.0 |
||||
CN#17 |
342r1 |
Forward Relocation Response without "RAB Setup Information" IE |
5.3.0 |
||||
CN#17 |
347 |
No equivalent Cause Code in GTP to "PDP context without TFT already activated" |
5.3.0 |
||||
CN#18 |
333r1 |
Support of mandatory IPv6 on the Iu interface |
5.4.0 |
||||
CN#18 |
348r4 |
Introduction of PCO IE in session management messages used in the MS Initiated PDP Context Deactivation procedure (direction MS to NW) |
5.4.0 |
||||
CN#18 |
350r1 |
Clarification on the inclusion of TEID II in SGSN Context Ack |
5.4.0 |
||||
CN#18 |
354r1 |
Removal of limitation in the Create PDP Context Request message |
5.4.0 |
||||
CN#18 |
355 |
Introduction of PCO IE in session management messages used in the Network-Requested PDP Context Activation Procedure (direction NW to MS) |
5.4.0 |
||||
CN#18 |
356r1 |
Introduction of PCO IE in session management messages used in the GGSN-Initiated PDP Context Modification procedure (direction NW to MS) |
5.4.0 |
||||
CN#18 |
357r1 |
Introduction of PCO IE in session management messages used in the GGSN-Initiated PDP Context Deactivation Procedure (direction NW to MS) |
5.4.0 |
||||
CN#18 |
360r1 |
PDCP sequence numbers in SGSN Context Response |
5.4.0 |
||||
CN#18 |
362r3 |
Clarification of the placement of the fields in the PDP Context IE |
5.4.0 |
||||
CN#18 |
363r4 |
Enabling control of content served to subscribers based on their location |
5.4.0 |
||||
CN#18 |
373r2 |
Clarification on IP fragmentation over Iu interface |
5.4.0 |
||||
CN#18 |
375r2 |
Transfer of Charging characteristics in case of inter SGSN change |
5.4.0 |
||||
CN#18 |
382r1 |
Clarification on presence of optional fields in GTP header |
5.4.0 |
||||
CN#19 |
386r1 |
Reinstatement of cause code version not supported |
5.5.0 |
||||
CN#19 |
387 |
Correction on the handling of PCO |
5.5.0 |
||||
CN#19 |
388 |
Removal of the N3-BUFFER-SIZE parameter |
5.5.0 |
||||
CN#19 |
389 |
Correction of presence requirement for the PCO IE |
5.5.0 |
||||
CN#19 |
395r3 |
TEID for GTP-C messages related to unknown PDP Contexts |
5.5.0 |
||||
CN#19 |
399 |
Correction of GTP’ references |
5.5.0 |
||||
CN#19 |
402r2 |
IPv4 and IPv6 form of Charging Gateway Address |
5.5.0 |
||||
CN#19 |
390r1 |
Introduction of SGSN Number in SGSN Context Request message |
6.0.0 |
||||
CN#19 |
403 |
Introduction of SGSN Number in the Forward Relocation Response message |
6.0.0 |
||||
CN#20 |
408r1 |
Correction for PDP Context Response with no PDP Contexts |
6.1.0 |
||||
CN#20 |
410 |
Controlling compression performed on the SGSN |
6.1.0 |
||||
CN#20 |
412r1 |
Enhancement of description for error codes for Create PDP Context response message |
6.1.0 |
||||
CN#20 |
420r2 |
Definition of reserved TEID value |
6.1.0 |
||||
CN#20 |
422 |
QoS Profile Data parameter in the Quality of Service (Data) Profile IE extended with one octet |
6.1.0 |
||||
CN#20 |
424 |
IMEISV to be included in the Container within the MM Context |
6.1.0 |
||||
CN#21 |
434 |
Correction of incorrect reference to a withdrawn specification |
6.2.0 |
||||
CN#21 |
436r1 |
Removal of End User Address from Create Subsequent PDP Context Response |
6.2.0 |
||||
CN#21 |
448r2 |
Correction/Clarification of GTP Cause Value |
6.2.0 |
||||
CN#21 |
453r2 |
Correction/Clarification of SGSN handling of Update PDP Context Response |
6.2.0 |
||||
CN#21 |
455 |
Change of Early UE feature to PUESBINE |
6.2.0 |
||||
CN#22 |
457 |
Removal of RAB Context IE in Forward Relocation Request |
6.3.0 |
||||
CN#22 |
461 |
Correction of Sequence Number Up handling |
6.3.0 |
||||
CN#22 |
477 |
Correction of incorrect reference to a withdrawn specification |
6.3.0 |
||||
CN#22 |
463r3 |
HSDPA impacts to GTP |
6.3.0 |
||||
CN#22 |
469r2 |
Introducing MBMS |
6.3.0 |
||||
CN#23 |
431r3 |
Enhancement of Recovery IE to reduce number of dangling PDP Contexts |
6.4.0 |
||||
CN#23 |
465r3 |
Controlling the creation of multiple, concurrent PDP Contexts |
6.4.0 |
||||
CN#23 |
480r1 |
Introduction of the MBMS Support Indication extension header |
6.4.0 |
||||
CN#23 |
481r2 |
Clarification in the definition of the QoS Profile IE encoding |
6.4.0 |
||||
CN#23 |
482r1 |
PDCP and GTP-U sequence numbers received in the PDP Context information element inside SGSN Context Response message |
6.4.0 |
||||
CN#23 |
483 |
Corrections to the Common Flags IE |
6.4.0 |
||||
CN#23 |
484 |
Change to the definition of GTP Tunnel for MBMS |
6.4.0 |
||||
CN#23 |
485 |
Removal of the GGSN address for Contorol Plane in the Delete MBMS Context Request |
6.4.0 |
||||
CN#24 |
478r4 |
Provision of S-CDR information to the GGSN |
6.5.0 |
||||
CN#24 |
486r2 |
Support of Inter-SGSN RA update for MBMS |
6.5.0 |
||||
CN#24 |
488r2 |
Automatic Device Detection (ADD) support in Inter-SGSN Routing Area Update procedures |
6.5.0 |
||||
CN#24 |
493 |
Change the attribution of Radio Priority LCS from TV to TLV |
6.5.0 |
||||
CN#24 |
495r1 |
Addition of BM-SC initiated De-registration |
6.5.0 |
||||
CN#24 |
496r1 |
Addition of TMGI |
6.5.0 |
||||
CN#24 |
497 |
Another Cause for MBMS Notification Reject Request |
6.5.0 |
||||
CN#24 |
498r1 |
Clarification of the Target Identification IE |
6.5.0 |
||||
CN#25 |
501 |
Alignment and enhancement of the "RAT Type" IE |
6.6.0 |
||||
CN#25 |
502 |
Corrections to charging information IEs |
6.6.0 |
||||
CN#25 |
507r1 |
RIM transparent routing |
6.6.0 |
||||
CN#25 |
511 |
Handling of ciphering and integrity keys at inter-SGSN RAU |
6.6.0 |
||||
CN#25 |
505 |
Error Indication during an ongoing MBMS data transfer |
6.6.0 |
||||
CN#25 |
506 |
Addition of Recovery IE in MBMS |
6.6.0 |
||||
CN#25 |
510r2 |
Introduction of a transparent container field for MBMS |
6.6.0 |
||||
CN#25 |
512 |
SGSN Context Request and IMSI |
6.6.0 |
||||
CN#26 |
520r1 |
Additional support of IPv4 and IPv6 node addresses in Create PDP and MBMS context procedures |
6.7.0 |
||||
CN#26 |
513r1 |
Clarification on the usage of the Alternative GGSN Address |
6.7.0 |
||||
CN#26 |
514r1 |
Addition of IEs to MBMS Session Start Request message |
6.7.0 |
||||
CN#26 |
515r1 |
Introduction of MBMS support indication between SGSNs |
6.7.0 |
||||
CN#26 |
524 |
GTP-C tunnel for MBMS broadcast |
6.7.0 |
||||
CN#27 |
534r1 |
Add Source RNC PDCP context info IE in Forward SRNS Context message |
6.8.0 |
||||
CN#27 |
470r7 |
Additional Trace Information |
6.8.0 |
||||
CN#27 |
528r2 |
Clarification to error handling of IEs of type TV |
6.8.0 |
||||
CN#27 |
529r1 |
Introduction of Hop Counter to Identification Request and SGSN Context Request |
6.8.0 |
||||
CN#27 |
530 |
Update of references to charging specifications |
6.8.0 |
||||
CN#27 |
531 |
Providing the BM-SC with approximate UE location information at MBMS context activation |
6.8.0 |
||||
CN#27 |
535r1 |
Clarification of IPv4 and IPv6 node addresses in the SRNS Relocation Procedure. |
6.8.0 |
||||
CN#27 |
536r1 |
Support of IPv4 and IPv6 node addresses in Inter-SGSN RAU procedure |
6.8.0 |
||||
CN#27 |
537r1 |
Add the Common Flags IE to GGSN-Initiated Update PDP Context Request message |
6.8.0 |
||||
CN#27 |
538r1 |
Addition of Selected PLMN-ID for network sharing |
6.8.0 |
||||
CN#27 |
539 |
Correction of type values |
6.8.0 |
||||
CN#27 |
540r1 |
Clarification of PCO IE in Update PDP context response |
6.8.0 |
||||
CN#27 |
543r1 |
Management Based Trace Activation Signalling |
6.8.0 |
||||
CN#27 |
544 |
Addition of RIM Routing Address for GERAN |
6.8.0 |
||||
CN#27 |
546r1 |
Adding missing parameters to the MBMS Session Start Request message |
6.8.0 |
||||
CN#27 |
547r1 |
Enhanced NSAPI for MBMS |
6.8.0 |
||||
CN#27 |
549 |
Change of newly added IEs in Rel 6 to type TLV |
6.8.0 |
||||
CN#27 |
550 |
Correction to Radio Priority LCS IE |
6.8.0 |
||||
CT#28 |
532r2 |
Correction to charging information for MBMS |
6.9.0 |
||||
CT#28 |
554r3 |
IE description to allow Signalling Activated Trace of the BM-SC |
6.9.0 |
||||
CT#28 |
555r1 |
Reference update following incorrectly implemented CR537 |
6.9.0 |
||||
CT#28 |
556 |
MBMS Session Duration |
6.9.0 |
||||
CT#29 |
558 |
Correction to encoding of MBMS information elements |
6.10.0 |
||||
CT#29 |
560 |
Correct type value of Radio Priority LCS Information Element |
6.10.0 |
||||
CT#29 |
563r2 |
MBMS Session Identity Repetition number |
6.10.0 |
||||
CT#29 |
564r1 |
Time to Data transfer |
6.10.0 |
||||
CT#30 |
0565 |
Inter-system Intra-SGSN change |
6.11.0 |
||||
CT#30 |
0569 |
MBMS Time to data transfer IE coding |
6.11.0 |
||||
CT#30 |
0568 |
PS handover procedure in GERAN A/Gb mode |
6.11.0 |
||||
CT#30 |
0570 |
New cause IE for PS Handover |
6.11.0 |
||||
CT#30 |
0566r2 |
Clarification of format for IMEI IE |
7.0.0 |
||||
CT#31 |
0572r1 |
Adding Required MBMS Bearer Capabilities IE to MBMS Registration Response |
7.1.0 |
||||
CT#31 |
0574r1 |
Introduction of RAT Type in SGSN Context Request message |
7.1.0 |
||||
CT#31 |
0580 |
SGSN Address for User-Plane Data Forwarding in Inter-RAT PS Handover |
7.1.0 |
||||
CT#32 |
0587r3 |
Indication of activity status for PDP Context |
7.2.0 |
||||
CT#32 |
0581r1 |
Misalignment between 23.060, 29.060 and 24.008 for the De-activation of a PDP Context |
7.2.0 |
||||
CT#32 |
0582r2 |
Clarification on usage of IEI definition in container of MMcontext |
7.2.0 |
||||
CT#32 |
0588r1 |
GTP Path Failure Changes |
7.2.0 |
||||
CT#32 |
0584 |
PS Handover List of PFCs |
7.2.0 |
||||
CT#32 |
0590r1 |
PS Handover corrections |
7.2.0 |
||||
CT#32 |
0600r2 |
Modification of parameters for Forward Relocation Request |
7.2.0 |
||||
CT#32 |
0604r1 |
Cell ID IE correction |
7.2.0 |
||||
CT#32 |
0607r1 |
Addition of RIM Routing Address Discriminator IE |
7.2.0 |
||||
CT#32 |
0609 |
NSAPI length correction |
7.2.0 |
||||
CT#33 |
0592r1 |
SGSN indication of RAB setup complete at Secondary PDP context activation |
7.3.0 |
||||
0612r1 |
PS HO correction |
||||||
0614r2 |
MBMS TEID Corrections |
||||||
0616 |
PS HO tunnelling |
||||||
0618r1 |
RIM Routing Address Correction |
||||||
0619r1 |
MBMS Session Update |
||||||
0621 |
Inclusion of the MBMS Counting Information Indication to the MBMS Session Start Request message |
||||||
CT#34 |
0610r3 |
Support for location based charging models in GPRS |
7.4.0 |
||||
0622r1 |
DSCR due to low traffic |
||||||
0624r1 |
Amendements to MBMS Registration procedure |
||||||
0625r2 |
Amendements to MBMS Session Start procedure |
||||||
0626 |
Amendements to MBMS Session Update procedure |
||||||
0632r2 |
MBMS Session Repetition Number Correction |
||||||
0635 |
GTP Path Failure Changes to MBMS |
||||||
0637r1 |
Missing address in MBMS Notification Reject Request |
||||||
0640r2 |
Clarification on presence of Teardown indicator |
||||||
CT#35 |
0627r7 |
Direct Tunnel Indication |
7.5.0 |
||||
0630r2 |
Update PDP context without negotiation |
||||||
0633r6 |
Additions for support of Network-Initiated QoS |
||||||
0641r1 |
Addition of Cause for MBMS Session Start Response |
||||||
0643r1 |
Mapping between BSSGP and RANAP cause values for PS HO |
||||||
0645r2 |
Direct Tunnel functionality – RNC failure |
||||||
0646r1 |
Clarifications to IMEI(SV) coding definition |
||||||
0649r2 |
Correction to a wrong refernce for TMGI definition |
||||||
0651 |
Correction to the Additional Trace Info IE |
||||||
0652 |
Correction of reserved bits |
||||||
March 2003 |
The Error Indication (EI) moved into 7.7.81. Tables and figures information removed. |
7.5.1 |
|||||
CT#36 |
0648r2 |
Correction to the length of the MBMS Session Duration IE |
7.6.0 |
||||
0654 |
Correction to the APN IE definition |
||||||
0655r1 |
Usage of Echo Request / Response for MBMS |
||||||
0658 |
Error Indications between RNC and GGSN in the case of Direct Tunnelling |
||||||
0659r2 |
NSAPI in Create PDP Context Response |
||||||
CT#36 |
0656 |
Extendibility of TLV coded IEs |
8.0.0 |
||||
CT#37 |
0661r1 |
TFT in Initiate PDP Context Activation Request message |
8.1.0 |
||||
0671 |
Correction to the User Location Information procedure |
||||||
0672 |
PDP contexts with upwards QoS negotiation |
||||||
0673 |
Target Identification encoding |
||||||
0674 |
QoS Extension |
||||||
CT#38 |
0680 |
Direct Tunnel Correction |
8.2.0 |
||||
0681 |
Specification Update of GBR and MBR due to MIMO |
||||||
0682r1 |
Aligning GTPv1 spec with Rel-7 RAN specs on RNC merged with NodeB feature |
||||||
CT#39 |
0684 |
Correction of location reporting |
8.3.0 |
||||
CT#40 |
0686r1 |
Essential correction to the Initiate PDP Context Activation Response message |
8.4.0 |
||||
CT#41 |
0688r1 |
MBMS Flow Identifier |
8.5.0 |
||||
0690 |
MBMS Reject |
||||||
0692 |
Changes due to bearer mapping for NRSPCA |
||||||
0693r1 |
Removing support for GTPv0 from R8 GTPv1 |
||||||
0696r1 |
Clarification on the format of TMGI |
||||||
CT#42 |
0697r1 |
Reference to 29.281 as normative for User Plane |
8.6.0 |
||||
0699 |
Essential correction to RAT Type handling in Update PDP Context Request message |
||||||
CT#43 |
0701 |
Adding UE Network Capability IE to GTPv1-C |
8.7.0 |
||||
0702 |
Cause Codes for NRSPCA |
||||||
0703r2 |
ARP correction |
||||||
0704r1 |
GERAN, UTRAN and E-UTRAN DRX parameter |
||||||
CT#44 |
0705r2 |
IE Ordering in MBMS Session Start Request |
8.8.0 |
||||
0706r3 |
MBMS for HSPA Evolution |
||||||
CT#45 |
0709r1 |
Cause code to resolve race condition between UE-initiated and NW-initiated secondary PDP context activation |
8.9.0 |
||||
0710 |
ARP in QoS correction |
||||||
0714r3 |
Clarifications to DT functionality |
||||||
0716 |
P-TMSI Signature for Suspend Request |
||||||
CT#45 |
0711r1 |
Dual stack support in GTPv1 |
9.0.0 |
||||
CT#46 |
0734r2 |
Addition of "Reliable INTER RAT PS HANDOVER" indicator |
9.1.0 |
||||
0730r1 |
Enhanced handling of RFSP index at the SGSN. GTPv1 |
||||||
0735 |
Essential correction to the PDP type in the End User Address IE |
||||||
0719r2 |
GGSN FQDN |
||||||
0720r4 |
Evolved ARP |
||||||
0721r1 |
Unauthenticated or missing IMSI for Emergency Service |
||||||
0722 |
MS TimeZone and ULI included in Resp messages |
||||||
0723r4 |
Support for CSG based charging |
||||||
0725 |
Updating the Error Indication clause |
||||||
0728 |
PDP Context Updated for Dual Stack Support in GTPv1 |
||||||
CT#47 |
0744r1 |
Data forwarding for GTPv1 |
9.2.0 |
||||
0741r2 |
Include CSG ID and CSG Membership Indication in Gn |
||||||
0739r1 |
Resolving ambiguity for Target Identification IE coding |
||||||
0747r1 |
Corrections to the RAN Information Management procedures |
||||||
0748 |
BCM violation in GGSN |
||||||
CT#48 |
0749r1 |
Evolved ARP in Network Initiated Secondary PDP Context Activation |
9.3.0 |
||||
0752r1 |
End Marker |
||||||
CT#49 |
0754r1 |
UE-AMBR and APN-AMBR for Gn/Gp SGSN |
9.4.0 |
||||
0763r1 |
Dual Stack IP address |
||||||
0764r1 |
Co-located GGSN-PGW FQDN |
||||||
0756r2 |
CSG Information Reporting Action |
||||||
0760r1 |
Dual Stack IP address |
||||||
0759r2 |
Essential correction to MS Info Change Notification Request |
||||||
0765r3 |
MS Info Change Reporting Support Indication |
||||||
0762r2 |
Critical deficiency in Gn/Gp SGSN to MME TAU procedure |
||||||
CT#50 |
0780r1 |
MS Time Zone adjustments |
9.5.0 |
||||
0773r4 |
Resolving GTPv1-C backward compatibility problems for the MM and PDP Context IEs in Rel-9 onwards |
||||||
0778r4 |
Invalid IE Length |
||||||
0767r1 |
S1-AP/RANAP/BSSGP Cause Code mapping in MME during IRAT HO involving Gn/Gp-SGSN |
||||||
0781 |
Cause for dual stack PDP context |
||||||
CT#50 |
0776r1 |
Echo Request & Echo Response |
10.0.0 |
||||
CT#51 |
0790r1 |
APN-AMBR IE |
10.1.0 |
||||
0792r4 |
Subscribed UE-AMBR in mobility procedure |
||||||
0795r1 |
Passing Charging Characteristics for IRAT |
||||||
0800r1 |
Essential correction to the encoding of Target RNC-ID |
||||||
0783r3 |
APN based congestion control |
||||||
0784r2 |
Low access priority indicator |
||||||
0785r6 |
APN-AMBR with NSAPI clarification |
||||||
0803r1 |
Correcting presence conditions for create PDP context response |
||||||
0793r4 |
Unsupported Secondary PDP Context Handling for LIPA |
||||||
0798r1 |
Introduction of "Reactivation Requested" cause in Delete PDP Context Request message |
||||||
CT#52 |
0823r1 |
Incorrect PCO handling at the GGSN |
10.2.0 |
||||
0812r1 |
Higher bitrates than 16 Mbps flag |
||||||
0816r1 |
Correction on PDP Type Number |
||||||
0808r2 |
Mapping of ASN.1/PER parameters to GTPv1 IEs |
||||||
0815r1 |
Signalling Indication |
||||||
0817 |
LAPI during UE initiated bearer resource allocation / modification procedures |
||||||
0809 |
Correcting the presence conditions of various GTP messages |
||||||
0813r2 |
Max MBR/APN-AMBR |
||||||
0814r3 |
Inactive Emergency PDN Handling |
||||||
CT#53 |
0829r1 |
PCO handling at the GGSN for pre-Rel 7 SGSNs |
10.3.0 |
||||
0825r1 |
PS handover procedure for SRVCC |
||||||
0831r1 |
Essential correction to handling of EPDN session for UICCless UE |
||||||
0836r1 |
RANAP Cause code range alignment with RANAP specification |
||||||
0838 |
PDU Notification Request correction for dual address PDP |
||||||
CT#53 |
0839r1 |
Correction to references |
11.0.0 |
||||
CT#54 |
0841r3 |
Referencing Information Elements defined outside GTP |
11.1.0 |
||||
0845r2 |
MBMS IP Multicast Distribution |
||||||
0851r2 |
New PDP type due to network preference |
||||||
0854r1 |
IMEI not known cause |
||||||
0856r1 |
PDP context for emergency call |
||||||
0846r1 |
Clarification on the length restriction of PCO, TFT IE |
||||||
0852r1 |
Clarification on appropriate usage of cause values |
||||||
0849r1 |
Defining the fixed number of octets for extendable IEs |
||||||
CT#55 |
0861 |
Handover to CSG cell with emergency bearer |
11.2.0 |
||||
0864 |
Pre-Rel-7 QoS description correction |
||||||
0871r1 |
Missing CSG Information Reporting Action IE in CPC and UPC response messages |
||||||
0881r2 |
Higher bitrates than 16 Mbps flag |
||||||
0873r1 |
Location change reporting support indication related correction |
||||||
0875r1 |
Inclusion of ULI and MS Time Zone IEs in DPC Request |
||||||
0878r1 |
Max MBR/APN-AMBR in enhanced SRNS relocation procedure |
||||||
0865 |
PDN connection concept in GTPv1 |
||||||
0866r1 |
Target ID |
||||||
0867 |
MBMS IP Multicast Distribution |
||||||
0868 |
Charging Characteristics |
||||||
0876r1 |
MS Info Change Reporting messages on existing non-zero TEID |
||||||
CT#56 |
0902r2 |
Providing Serving Network Information to the GGSN |
11.3.0 |
||||
0889r1 |
GGSN TEID and IP address in the Update PDP Context Response message |
||||||
0883r3 |
Network provided Location Information |
||||||
0884 |
Reference of RNC Failure |
||||||
0890 |
NSAPI in GTPv1 |
||||||
0891r1 |
Additions for CS to PS SRVCC |
||||||
0894r1 |
Corrections to handling mechanism when receiving restart counter in Echo Response |
||||||
0895r1 |
Inclusion of EARP in the CPC Request message of the secondary PDP Context |
||||||
0896 |
UCI encoding correction for two digit MNC |
||||||
0901r1 |
Mapping between Gn/Gp and NAS Cause values |
||||||
0908r1 |
Extended RNC ID in Target Identification IE |
||||||
0910r1 |
Echo Request message |
||||||
CT#57 |
0911r1 |
PS only subscription w/o MSISDN |
11.4.0 |
||||
0913r1 |
eNodeB Identification |
||||||
0915r1 |
Reference list correction to align with the corrected TS 29.212 title |
||||||
CT#58 |
0917r1 |
Removal of Maximum MBR/APN-AMBR |
11.5.0 |
||||
0914r4 |
Adding a Cause Value in Delete Context PDP Request message |
||||||
0918r2 |
Clarifications on value definitions of MBMS 2G/3G Indicator and Source Type in Cell Identification |
||||||
0921r1 |
Clarifications on RAT Type Values "UTRAN" and "HSPA evolution" |
||||||
0924r1 |
PS only subscription without MSISDN |
||||||
0925 |
Corrections to definitions of MBMS UE Context IE |
||||||
CT#59 |
0932r1 |
Addition of PS to CS handover indication in Delete PDP Context Request |
11.6.0 |
||||
0933r2 |
Populating Serving Network in RAI |
||||||
0939r1 |
Providing Selection Mode IE during handover/RAU procedures |
||||||
CT#59 |
0927r2 |
GTPv1 deferred IPv4 address allocation |
12.0.0 |
||||
0928r1 |
Corrections to descriptions of RFSP Index |
||||||
0929r1 |
Clarification on IE Type Value in the GTP signalling message |
||||||
0935r1 |
Clean up the references |
||||||
CT#60 |
0947r2 |
ULI Timestamp |
12.1.0 |
||||
0944r3 |
Clarification on the use of eARP IE |
||||||
0942r3 |
Clarification on how to indicate UE has left a CSG cell |
||||||
0941r1 |
SIPTO at the local network |
||||||
CT#61 |
0950r2 |
Enforcing access restriction during I-RAT RAU/TAU procedures |
12.2.0 |
||||
0960r2 |
Correction to the condition of inclusion of the RAT Type IE |
||||||
0961r2 |
SIPTO at the Local Network |
||||||
0962r1 |
GERAN Iu Mode |
||||||
0964r2 |
ULI Timestamp IE format |
||||||
CT#62 |
0965 |
Correction on the occurrence of LHN ID with NSAPI |
12.3.0 |
||||
0966 |
Core Network Operator selection origin |
||||||
0968r1 |
Correct BSSGP Cause value |
||||||
0969 |
Resolving ambiguity of SGSN Number IE encoding |
||||||
0970r1 |
Clarification on encoding of bit rates when converting bits per second received over Diameter and MAP interfaces to kilo bits per second over GTPv1. |
||||||
0971r1 |
Cause IE condition in the Delete PDP Context Request |
||||||
CT#63 |
0978r1 |
RFSP index encoding during inter SGSN mobility procedure |
12.4.0 |
||||
0982r1 |
Update the ULI Timestamp IE format |
||||||
0975r2 |
CSG Membership Indication values |
||||||
0979r2 |
PLMN ID communicated to the HPLMN in network sharing |
||||||
0980 |
MS Info Change Notification |
||||||
CT#64 |
0983r1 |
Number of authentication vectors in the MM Context IE |
12.5.0 |
||||
0984r1 |
Context Response with P-TMSI Signature mismatch |
||||||
0985r1 |
Correction on encoding of Selected PLMN ID and Target Identification |
||||||
0986r1 |
Correction of reference of transparent container |
||||||
CT#65 |
0992r1 |
Corrections to E-UTRAN to GERAN PS Handover |
12.6.0 |
||||
0987 |
P-CSCF Restoration Indication |
||||||
0988r2 |
ULI change reporting when RAB/user plane is established |
||||||
0993 |
Dual Address Bearer Flag |
||||||
0994r1 |
Correct procedure name for PDN connection deactivation |
||||||
CT#66 |
0998r2 |
Target Cell Identification in E-UTRAN to GERAN PS Handover |
12.7.0 |
||||
0999r1 |
RANAP cause in Relocation Cancel Request |
||||||
1000r1 |
Data forwarding during Gn SGSN to S4-SGSN RAU |
||||||
1001r1 |
IEs order in MBMS Registration Response and MS Info Change Notification Response |
||||||
1002r1 |
Removal of invalid description on spare bits in MBMS UE Context IE |
||||||
1003r2 |
MS Info Change Reporting Action IE |
||||||
1004r3 |
Terminology cleanup for Location Change Reporting |
||||||
CT#67 |
1010 |
Reserved Extension Header Value for GTP-U |
12.8.0 |
||||
1011r1 |
Cleanup Error Indication Definition |
||||||
1013 |
MS Info Change Reporting Action IE |
||||||
CT#67 |
1006r1 |
UE Registration Query |
13.0.0 |
||||
1008r1 |
ULI RAI LAC encoding |
||||||
1009 |
Cause IMSI not known |
||||||
CT#68 |
1015r1 |
RAT Type in MS Info Change Notification Request |
13.1.0 |
||||
1016r1 |
Clarifications to inclusion of Linked NSAPI in MS Info Change Notification Request |
||||||
1019r1 |
Correction to inclusion of PTMSI Signature in SGSN Context Request message for Suspend Procedure |
||||||
1018r1 |
PLMN ID communicated in the VPLMN in network sharing |
||||||
CT#69 |
1025r1 |
eDRX impact for network originated control plane procedure |
13.2.0 |
||||
1026r1 |
TAU/RAU with data forwarding for buffered DL data |
||||||
1027r3 |
UE Usage Type for Dedicated Core Network Feature |
||||||
1028r3 |
Reject Cause in SGSN Context Acknowledge for Dedicated Core Network Feature |
||||||
CT#70 |
1029r1 |
Transferring DTCI and PNSI during inter SGSN mobility procedure |
13.3.0 |
||||
1030r1 |
IE type extension |
||||||
1031 |
Delay Tolerant Connection Indication |
||||||
CT#71 |
1032r1 |
Incorrect use of the term "full hexadecimal representation" to mean binary encoding |
13.4.0 |
||||
1033r1 |
Delay Tolerant Connection Indication |
||||||
1034r1 |
Triggering MT SM retransmission by the SMS GMSC to a UE in eDRX during inter MME/SGSN mobility procedure for GTPv1 |
||||||
2016-06 |
CT#72 |
CP-160234 |
1039 |
1 |
Extensions for EGPRS access security enhancements |
13.5.0 |
|
2016-06 |
CT#72 |
CP-160217 |
1035 |
2 |
Protocol Change for introducing new non-IP PDN Type |
14.0.0 |
|
2016-06 |
CT#72 |
CP-160217 |
1036 |
3 |
Transfer of non-IP PDN during Inter-SGSN RAU and PS HO Procedure |
14.0.0 |
|
2016-09 |
CT#73 |
CP-160435 |
1040 |
2 |
Source SGSN behaviour if Target SGSN does not support CIoT optimizations |
14.1.0 |
|
2016-12 |
CT#74 |
CP-160675 |
1041 |
2 |
Inclusion of IMSI in the Modify Bearer Request message |
14.2.0 |
|
2016-12 |
CT#74 |
CP-160652 |
1043 |
1 |
New IE for IOV_updates counter |
14.2.0 |
|
2016-12 |
CT#74 |
CP-160659 |
1045 |
1 |
Extended Common Flags II in the Create PDP Context Response message |
14.2.0 |
|
2016-12 |
CT#74 |
CP-160659 |
1047 |
– |
The flag PMTSMI in Common Flag II |
14.2.0 |
|
2016-12 |
CT#74 |
CP-160680 |
1048 |
1 |
CR implementation error on the inclusion of SCEF PDN in a Forward Relocation Request Table |
14.2.0 |
|
2017-03 |
CT#75 |
CP-170027 |
1050 |
1 |
Node Identifier IE in Forward Relocation Response |
14.3.0 |
|
2017-03 |
CT#75 |
CP-170040 |
1051 |
2 |
RAB Setup information in the IRAT handover |
14.3.0 |
|
2017-09 |
CT#77 |
CP-172025 |
1052 |
2 |
Clarification on Rejection Cause Handling |
15.0.0 |
|
2017-12 |
CT#78 |
CP-173023 |
1055 |
1 |
PGW-U selection based on Mapped UE Usage Type with Gn SGSNs |
15.1.0 |
|
2017-12 |
CT#78 |
CP-173036 |
1053 |
1 |
Selection of PGWs optimized for NR with Gn SGSNs |
15.1.0 |
|
2017-12 |
CT#78 |
CP-173036 |
1057 |
2 |
Access Restrictions to NR as Secondary RAT on MM Context |
15.1.0 |
|
2017-12 |
CT#78 |
CP-173031 |
1056 |
2 |
GGSN/PGW IPv4v6 address |
15.1.0 |
|
2018-03 |
CT#79 |
CP-180020 |
1060 |
1 |
Condition correction for PGW-U selection based on DCNR |
15.2.0 |
|
2018-12 |
CT#82 |
CP-183096 |
1061 |
2 |
Alternative GGSN addresses for control Plane and user traffic |
15.3.0 |
|
2019-03 |
CT#83 |
CP-190033 |
1062 |
– |
GGSN control plane and user plane addresses |
15.4.0 |
|
2019-03 |
CT#83 |
CP-190033 |
1063 |
1 |
Correction to the SGSN-Initiated Update PDP Context Request |
15.4.0 |
|
2019-06 |
CT#84 |
CP-191025 |
1064 |
1 |
IP addressing between IPv4/IPv6 capable SGSN and GGSN |
15.5.0 |
|
2019-06 |
CT#84 |
CP-191025 |
1065 |
– |
IP addressing between IPv4/IPv6 capable SGSN/GGSN during intra-SGSN scenarios |
15.5.0 |
|
2020-03 |
CT#87e |
CP-200046 |
1066 |
3 |
Clarification to the Target Identification and eNodeB ID usage |
16.0.0 |
|
2021-03 |
CT#91e |
CP-210033 |
1068 |
1 |
Reserve some IE types for GTP-U |
17.0.0 |
|
2021-09 |
CT#91e |
CP-212046 |
1069 |
1 |
F |
Minor Corrections |
17.1.0 |
2022-03 |
CT#95e |
CP-220089 |
1070 |
1 |
F |
Incorrect references and IE names |
17.2.0 |
2022-06 |
CT#96 |
CP-221048 |
1071 |
1 |
A |
Alternative GGSN Addresses for Control Plane and User Traffic IEs |
17.3.0 |
2022-09 |
CT#97e |
CP-222049 |
1074 |
– |
F |
Removal of Editor’s Note |
17.4.0 |