Priority Level

M

INTEGER(0..15)

This IE indicates the priority of the request.

Usage:

Value “0” means “Spare”; It shall be treated as a logical error if received.

Values between 1 and 14 are ordered in decreasing order of priority, “1” being the highest and “14” the lowest.

Value “15” means “No Priority”.

Pre-emption Capability

M

ENUMERATED(shall not trigger pre-emption, may trigger pre-emption)

Pre-emption Vulnerability

M

ENUMERATED(not pre-emptable, pre-emptable)

Allowed Queuing Time

INTEGER(1..60)

Unit: Seconds.

Allowed UL Rate

O

INTEGER(1..maxNrOfTFs)

“1”: TFI 0,

“2”: TFI 1,

“3”: TFI 2,

…

Allowed DL Rate

O

INTEGER(1..maxNrOfTFs)

“1”: TFI 0,

“2”: TFI 1,

“3”: TFI 2,

…

Direction of Altitude

M

ENUMERATED(Height, Depth)

Altitude

M

INTEGER(

0..2¹⁵-1)

The relation between the value (N) and the altitude (a) in meters it describes is N a <N+1, except for N=2¹⁵-1 for which the range is extended to include all grater values of (a).

Antenna Co-location Indicator

ENUMERATED(co-located,…)

Alternative Format Reporting Indicator

ENUMERATED (Alternative format is allowed, …)

Binding ID

OCTET STRING (SIZE(1..4,…))

If the Binding ID includes an UDP port, the UDP port is included in octet 1 and 2. The first octet of the UDP port field shall be included in the first octet of the Binding ID.

BLER

INTEGER(-63..0)

Step 0.1. (Range –6.3…0).

It is the Log10 of the BLER.

Burst Start

M

INTEGER(0..15)

See TS 25.214 [10] and TS 25.224 [22].

Burst Length

M

INTEGER(10..25)

See TS 25.214 [10] and TS 25.224 [22].

Burst freq

M

INTEGER(1..16)

See TS 25.214 [10] and TS 25.224 [22].

CHOICE Cause Group

M

>Radio Network Layer

>>Radio Network Layer Cause

M

ENUMERATED
(Unknown C-ID,
Cell not Available,
Power Level not Supported,
UL Scrambling Code Already in Use,
DL Radio Resources not Available,
UL Radio Resources not Available,

Measurement not Supported For The Object,
Combining Resources Not Available,

Combining not Supported,
Reconfiguration not Allowed,
Requested Configuration not Supported,
Synchronisation Failure,

Requested Tx Diversity Mode not Supported,

Measurement Temporarily not Available,

Unspecified,

Invalid CM Settings,

Reconfiguration CFN not Elapsed,

Number of DL Codes Not Supported,

Dedicated Transport Channel Type not Supported,
DL Shared Channel Type not Supported,
UL Shared Channel Type not Supported,
Common Transport Channel Type not Supported,
UL Spreading Factor not Supported,
DL Spreading Factor not Supported,

CM not Supported,

Transaction not Supported by Destination Node B,

RL Already Activated/Allocated,

…,

Number of UL Codes Not Supported,

Cell reserved for operator use,

DPC Mode Change not Supported,

Information temporarily not available,

Information Provision not supported for the object,

Power Balancing status not compatible,

Delayed Activation not Supported,

RL Timing Adjustment Not Supported, Unknown RNTI,

Measurement Repetition Rate not Compatible with Current Measurements,

UE not Capable to Implement Measurement,

F-DPCH not supported,

E-DCH not supported,

Continuous Packet Connectivity DTX-DRX operation not supported,

Continuous Packet Connectivity HS-SCCH less operation not supported,

MIMO not supported,

E-DCH TTI2ms not supported,

Continuous Packet Connectivity DTX-DRX operation not available, Continuous Packet Connectivity UE DTX Cycle not available,

MIMO not available,

SixteenQAM UL not supported,

HS-DSCH MAC-d PDU Size Format not supported,

F-DPCH Slot Format operation not supported,

E-DCH MAC-d PDU Size Format not available,

E-DPCCH Power Boosting not supported,

Trelocprep Expiry,

Relocation Cancelled,

Traffic Load In The Target Cell Higher Than In The Source Cell,

Time critical Relocation,

Resource optimisation relocation, Relocation desirable for radio reasons ,

Directed Retry,

Reduce Load in Serving Cell,

No Iu CS UP relocation,

SixtyfourQAM DL and MIMO Combined not available,

Multi Cell operation not available,

Multi Cell operation not supported,

Semi-Persistent scheduling not supported,

Continuous Packet Connectivity DRX not supported,

Continuous Packet Connectivity DRX not available,

Enhanced Relocation not Supported,

Relocation Not Supported Due To PUESBINE Feature,

Relocation Failure In Target RNC, Relocation Target not allowed,

Requested Ciphering and/or Integrity Protection Algorithms not Supported, SixtyfourQAM DL and MIMO Combined not supported,

TX diversity for MIMO UE on DL Control Channels not available,

Single Stream MIMO not supported,

Single Stream MIMO not available,

Multi Cell operation with MIMO not available,

Multi Cell operation with MIMO not supported,

Multi Cell E-DCH operation not available,

Multi Cell E-DCH operation not supported,

Multi Cell operation with Single Stream MIMO not available,

Multi Cell operation with Single Stream MIMO not supported,

Cell Specific Tx Diversity Handling For Multi Cell Operation Not Available,

Cell Specific Tx Diversity Handling For Multi Cell Operation Not Supported,

Frequency Specific Compressed Mode Not Available, Uplink Closed Loop Transmit Diversity Operation Not Available, Uplink Closed Loop Transmit Diversity Operation Not Supported, MIMO with four transmit antennas not supported, MIMO with four transmit antennas not available, Dual Stream MIMO with four transmit antennas not supported, Dual Stream MIMO with four transmit antennas not available, Multiflow operation not available, Multiflow operation not supported, SixtyfourQAM UL not available, SixtyfourQAM UL not supported, UL MIMO operation not available, UL MIMO operation not supported, UL MIMO and SixteenQAM operation not available, UL MIMO and SixteenQAM operation not supported, UL MIMO and SixtyfourQAM operation not available, UL MIMO and SixtyfourQAM operation not supported, E-DCH Decoupling operation not available, E-DCH Decoupling operation not supported, Basic DCH Enhancements operation not available, Basic DCH Enhancements operation not supported, Full DCH Enhancements operation not available, Full DCH Enhancements operation not supported, Radio Links without DPCH/F-DPCH operation not available, Radio Links without DPCH/F-DPCH operation not supported, UL DPCCH2 operation not available, UL DPCCH2 operation not supported, Downlink TPC enhancements operation not available, Downlink TPC enhancements operation not supported, Dual Cell E-DCH operation enhancements with 10ms and 10ms TTI operation not available, Dual Cell E-DCH operation enhancements with 10ms and 10ms TTI operation not supported, Dual Cell E-DCH operation enhancements with different TTI operation not available, Dual Cell E-DCH operation enhancements with differetn TTI operation not supported)

>Transport Layer

>>Transport Layer Cause

M

ENUMERATED
(Transport Resource Unavailable,

Unspecified,
…)

>Protocol

>>Protocol Cause

M

ENUMERATED
(Transfer Syntax Error,
Abstract Syntax Error (Reject),
Abstract Syntax Error (Ignore and Notify),
Message not Compatible with Receiver State,

Semantic Error,
Unspecified,

Abstract Syntax Error (Falsely Constructed Message),…)

>Misc

>>Miscellaneous Cause

M

ENUMERATED
(Control Processing Overload,
Hardware Failure,
O&M Intervention,
Not enough User Plane Processing Resources,
Unspecified,…)

Cell not Available

The concerned cell is not available.

Cell reserved for operator use

The concerned cell is reserved for operator use.

Cell Specific Tx Diversity Handling For Multi Cell Operation Not Available

Cell specific tx diversity handling for multi cell operation not available in the concerned cell(s).

Cell Specific Tx Diversity Handling For Multi Cell Operation Not Supported

The concerned cell(s) do not support the cell specific tx diversity handling for multi cell operation.

CM not Supported

The concerned cell(s) do not support Compressed Mode.

Combining not Supported

The DRNS does not support the RL combining for the concerned cells.

Combining Resources Not Available

The value of the received Diversity Control Field IE was set to “Must”, but the DRNS cannot perform the requested combining.

Common Transport Channel Type not Supported

The concerned cell(s) do not support the RACH and/or FACH Common Transport Channel Type.

Continuous Packet Connectivity DTX-DRX operation not available

CPC resources for DTX-DRX operation not available in the concerned cell(s).

Continuous Packet Connectivity DRX not available

HSPA resources for DRX operation not available in the concerned cell(s). (for 1.28Mcps TDD only).

Continuous Packet Connectivity DRX not supported

The concerned cell(s) do not support the Continuous Packet Connectivity DRX operation (for 1.28Mcps TDD only).

Continuous Packet Connectivity DTX-DRX operation not Supported

The concerned cell(s) do not support the Continuous Packet Connectivity DTX-DRX operation.

Continuous Packet Connectivity HS-SCCH less operation not Supported

The concerned cell(s) do not support the Continuous Packet Connectivity HS-SCCH less operation.

Continuous Packet Connectivity UE DTX Cycle not available

CPC resources for the UE DTX Cycle not available in the concerned cell(s).

Dedicated Transport Channel Type not Supported

The concerned cell(s) do not support the Dedicated Transport Channel Type.

Delayed Activation not Supported

The concerned cell(s) do not support delayed activation of RLs.

Directed Retry

The reason for action is Directed Retry.

DL Radio Resources not Available

The DRNS does not have sufficient DL radio resources available.

DL SF not Supported

The concerned cell(s) do not support the requested DL SF.

DL Shared Channel Type not Supported

The concerned cell(s) do not support the Downlink Shared Channel Type.

DPC Mode Change not Supported

The concerned cells do not support the DPC mode changes.

E-DCH MAC-d PDU Size Format not available

The selected E-DCH MAC-d PDU Size Format is not available in the concerned cell(s).

E-DCH not supported

The concerned cell(s) do not support E-DCH.

E-DCH TTI2ms not supported

The concerned cell(s) do not support the E-DCH 2ms TTI operation.

E-DPCCH Power Boosting not supported

The concerned cell(s) do not support the E-DPCCH Power Boosting.

Enhanced Relocation not Supported

The DRNS does not support the Enhanced Relocation.

F-DPCH not supported

The concerned cell(s) do not support the Fractional DPCH.

F-DPCH Slot Format operation not supported

The concerned cell(s) do not support the F-DPCH Slot Format operation.

MIMO with four transmit antennas not supported

The concerned cell(s) do not support the MIMO with four transmit antennas operation.

MIMO with four transmit antennas not available

MIMO with four transmit antennas resources not available in the concerned cell(s).

Dual Stream MIMO with four transmit antennas not supported

The concerned cell(s) do not support the Dual Stream MIMO with four transmit antennas operation.

Dual Stream MIMO with four transmit antennas not available

Dual Stream MIMO with four transmit antennas resources not available in the concerned cell(s).

Frequency Specific Compressed Mode not available

Frequency Specific Compressed Mode is not available in the concerned cell(s).

HS-DSCH MAC-d PDU Size Format not supported

The concerned cell(s) do not support the selected HS-DSCH MAC-d PDU Size Format.

Information Provision not supported for the object

The RNS doesn’t support provision of the requested information for the concerned object types.

Information temporarily not available

The RNS can temporarily not provide the requested information.

Invalid CM Settings

The concerned cell(s) consider the requested Compressed Mode settings invalid.

Measurement not Supported For The Object

At least one of the concerned cell(s) does not support the requested measurement on the concerned object type.

Measurement Repetition Rate not Compatible with Current Measurements

The requested parameters for a forwarded UE measurement are not compatible with the current measurement schedule in the SRNC.

Measurement Temporarily not Available

The DRNS can temporarily not provide the requested measurement value.

MIMO not available

MIMO resources not available in the concerned cell(s).

MIMO not supported

The concerned cell(s) do not support the MIMO operation.

Multi Cell E-DCH operation not available

Multi cell E-DCH operation is not available in the concerned cell(s).

Multi Cell E-DCH operation not supported

The concerned cell(s) do not support Multi cell E-DCH operation.

Multi Cell operation not available

Multi Cell operation resources not available in the concerned cell(s).

Multi Cell operation not supported

The concerned cell(s) do not support Multi Cell operation.

Multi Cell operation with MIMO not available

Multi Cell operation with MIMO resources not available in the concerned cell(s).

Multi Cell operation with MIMO not supported

The concerned cell(s) do not support Multi Cell operationwith MIMO.

Multi Cell operation with Single Stream MIMO not available

Multi Cell operation with Single Stream MIMO resources not available in the concerned cell(s).

Multi Cell operation with Single Stream MIMO not supported

The concerned cell(s) do not support Multi Cell operationwith Single Stream MIMO.

No Iu CS UP relocation

The relocation is triggered by CS call and the source RNC has no Iu CS user plane.

Number of DL Codes not Supported

The concerned cell(s) do not support the requested number of DL codes.

Number of UL Codes not Supported

The concerned cell(s) do not support the requested number of UL codes.

Power Balancing status not compatible

The power balancing status in the SRNC is not compatible with that of the DRNC.

Power Level not Supported

A DL power level was requested which the concerned cell(s) do not support.

Reconfiguration CFN not Elapsed

The requested action cannot be performed due to that a COMMIT message was received previously, but the concerned CFN has not yet elapsed.

Reconfiguration not Allowed

The SRNC does currently not allow the requested reconfiguration.

Reduce Load in Serving Cell

Load on serving cell needs to be reduced.

Relocation Cancelled

The reason for the action is relocation cancellation.

Relocation Desirable For Radio Reasons

The reason for requesting relocation is radio related.

Relocation Failure In Target RNC

Relocation failed due to a failure in target RNC.

Relocation Not Supported Due To PUESBINE Feature

The DRNS can not support the relocation due to the PUESBINE Feature.

Relocation Target not allowed

Relocation to the indicated target cell is not allowed for the UE in question.

Requested Ciphering And/Or Integrity Protection Algorithms Not Supported

The DRNS does not support the requested ciphering and/or integrity protection algorithms.

Requested Configuration not Supported

The concerned cell(s) do not support the requested configuration i.e. power levels, Transport Formats, physical channel parameters,…..

Requested Tx Diversity mode not Supported

The concerned cell(s) do not support the requested transmit diversity mode.

Resource Optimisation Relocation

The reason for requesting relocation is resource optimisation.

RL Already Activated/ Allocated

The DRNS has already allocated an RL with the requested RL ID for this UE Context.

RL Timing Adjustment not Supported

The concerned cell(s) do not support adjustments of the RL timing.

Semi-Persistent scheduling not supported

The concerned cell(s) do not support the Semi-Persistent scheduling operation (for 1.28Mcps TDD only).

SixteenQAM UL not Supported

The concerned cell(s) do not support the 16 QAM UL.

SixtyfourQAM DL and MIMO Combined not available

SixtyfourQAM DL and MIMO Combined not available in the concerned cell(s).

SixtyfourQAM DL and MIMO Combined not supported

The DRNS does not support SixtyfourQAM DL and MIMO Combined for the concerned cells.

Synchronisation Failure

Loss of UL Uu synchronisation.

Time Critical Relocation

Relocation is requested for time critical reason i.e. this cause value is reserved to represent all critical cases where the connection is likely to be dropped if relocation is not performed.

Traffic Load In The Target Cell Higher Than In The Source Cell

Relocation to reduce load in the source cell is rejected, as the target cell’s traffic load is higher than that in the source cell.

Transaction not Supported by Destination Node B

The requested action cannot be performed due to lack of support of the corresponding action in the destination Node B.

T_RELOCprep Expiry

Relocation Preparation procedure is cancelled when timer T_RELOCprep expires.

Single Stream MIMO not supported

The concerned cell(s) do not support the Single Stream MIMO.

Single Stream MIMO not available

Single Stream MIMO resources not available in the concerned cell(s).

TX diversity for MIMO UE on DL Control Channels not available

The DRNS does not have sufficient radio resources available to support transmit diversity on downlink control channels when the UE is configured in MIMO mode with P-CPICH & S-CPICH as phase references (TS 25.211 [8]).

UE not Capable to Implement Measurement

The UE is not capable to initiate/report a requested measurement due to its current state or capabilities.

UL Radio Resources not Available

The DRNS does not have sufficient UL radio resources available.

UL Scrambling Code Already in Use

The concerned UL scrambling code is already in use for another UE.

UL SF not Supported

The concerned cell(s) do not support the requested minimum UL SF.

UL Shared Channel Type not Supported

The concerned cell(s) do not support the Uplink Shared Channel Type.

Unknown C-ID

The DRNS is not aware of a cell with the provided C-ID.

Unknown RNTI

The SRNC or DRNC is not aware of a UE indicated with the provided RNTI.

Unspecified

Sent when none of the above cause values applies but still the cause is Radio Network Layer related.

Uplink Closed Loop Transmit Diversity Operation Not Available

Uplink Closed Loop Transmit Diversity Operation resources not available in the concerned cell(s).

Uplink Closed Loop Transmit Diversity Operation Not Supported

The concerned cell(s) do not support UL CLTD Operation.

Multiflow operation not available

Multiflow resources not available in the concerned cell(s).

Multiflow operation not supported

The concerned cell(s) do not support Multiflow operation.

SixtyfourQAM UL operation not available

SixtyfourQAM UL resources are not available in the concerned cell(s).

SixtyfourQAM UL operation not supported

The concerned cell(s) do not support SixtyfourQAM UL operation.

UL MIMO operation not available

UL MIMO resources are not available in the concerned cell(s).

UL MIMO operation not supported

The concerned cell(s) do not support UL MIMO operation.

UL MIMO and SixteenQAM operation not available

UL MIMO and SixteenQAM resources are not available in the concerned cell(s).

UL MIMO and SixteenQAM operation not supported

The concerned cell(s) do not support UL MIMO and SixteenQAM operation.

UL MIMO and SixtyfourQAM operation not available

UL MIMO and SixtyfourQAM resources are not available in the concerned cell(s).

UL MIMO and SixtyfourQAM operation not supported

The concerned cell(s) do not support UL MIMO and SixtyfourQAM operation.

E-DCH Decoupling operation not available

E-DCH Decoupling resources are not available in the concerned cell(s).

E-DCH Decoupling operation not supported

The concerned cell(s) do not support E-DCH Decoupling operation.

Basic DCH Enhancements operation not available

Basic DCH Enhancements resources are not available in the concerned cell(s).

Basic DCH Enhancements operation not supported

The concerned cell(s) do not support Basic DCH Enhancements operation.

Full DCH Enhancements operation not available

Full DCH Enhancements resources are not available in the concerned cell(s).

Full DCH Enhancements operation not supported

The concerned cell(s) do not support Full DCH Enhancements operation.

Radio Links without DPCH/F-DPCH operation not available

Radio Links without DPCH/F-DPCH resources are not available in the concerned cell(s).

Radio Links without DPCH/F-DPCH operation not supported

The concerned cell(s) do not support F-DPCH less operation.

UL DPCCH2 operation not available

UL DPCCH2 resources are not available in the concerned cell(s).

UL DPCCH2 operation not supported

The concerned cell(s) do not support UL DPCCH2 operation.

Downlink TPC enhancements operation not available

Downlink TPC enhancements resources are not available in the concerned cell(s).

Downlink TPC enhancements operation not supported

The concerned cell(s) do not support Downlink TPC enhancements operation.

Dual Cell E-DCH operation enhancements with 10ms and 10ms TTI operation not available

Dual Cell E-DCH operation enhancements with 10ms and 10ms TTI resources are not available in the concerned cell(s).

Dual Cell E-DCH operation enhancements with 10ms and 10ms TTI operation not supported

The concerned cell(s) do not support Dual Cell E-DCH operation enhancements with 10ms and 10ms TTI operation.

Dual Cell E-DCH operation enhancements with different TTI operation not available

Dual Cell E-DCH operation enhancements with different TTI resources are not available in the concerned cell(s).

Dual Cell E-DCH operation enhancements with different TTI operation not supported

The concerned cell(s) do not support Dual Cell E-DCH operation enhancements with different TTI operation.

Transport resource unavailable

The required transport resources are not available.

Unspecified

Sent when none of the above cause values applies but still the cause is Transport Network Layer related.

Abstract Syntax Error (Reject)

The received message included an abstract syntax error and the concerned criticality indicated “reject” (see subclause 10.3).

Abstract Syntax Error (Ignore and Notify)

The received message included an abstract syntax error and the concerned criticality indicated “ignore and notify” (see subclause 10.3).

Abstract syntax error (falsely constructed message)

The received message contained IEs or IE groups in wrong order or with too many occurrences (see subclause 10.3).

Message not Compatible with Receiver State

The received message was not compatible with the receiver state (see subclause 10.4).

Semantic Error

The received message included a semantic error (see subclause 10.4).

Transfer Syntax Error

The received message included a transfer syntax error (see subclause 10.2).

Unspecified

Sent when none of the above cause values applies but still the cause is Protocol related.

Control Processing Overload

DRNS control processing overload.

Hardware Failure

DRNS hardware failure.

Not enough User Plane Processing Resources

DRNS has insufficient user plane processing resources available.

O&M Intervention

Operation and Maintenance intervention related to DRNS equipment.

Unspecified

Sent when none of the above cause values applies and the cause is not related to any of the categories Radio Network Layer, Transport Network Layer or Protocol.

Cell GAI Geographical Co-ordinates

1 .. <maxNrOfPoints>

>Latitude Sign

M

ENUMERATED(North, South)

>Degrees of Latitude

M

INTEGER(

0..2²³-1)

The IE value (N) is derived by this formula:

N2²³ X /90  N+1

X being the latitude in degree (0°.. 90°).

>Degrees of Longitude

M

INTEGER(

-2²³..2²³-1)

The IE value (N) is derived by this formula:

N2²⁴ X /360  N+1

X being the longitude in degree (-180°..+180°).

maxNrOfPoints

Maximum no. of points in polygon.

CHOICE Cell GAI Additional Shapes

>GA Point With Uncertainty

>>GA Point with Uncertainty

M

9.2.1.30A

Ellipsoid point with uncertainty circle.

>GA Ellipsoid point with uncertainty Ellipse

>>GA Ellipsoid Point with Uncertainty Ellipse

M

9.2.1.30B

Ellipsoid point with uncertainty Ellipse.

>GA Ellipsoid point with altitude

>>GA Ellipsoid Point with Altitude

M

9.2.1.30C

Ellipsoid point with altitude.

>GA Ellipsoid point with altitude and uncertainty Ellipsoid

>>GA Ellipsoid Point with Altitude and Uncertainty Ellipsoid

M

9.2.1.30D

Ellipsoid point with altitude and uncertainty Ellipsoid.

>GA Ellipsoid Arc

>>GA Ellipsoid Arc

M

9.2.1.30E

Ellipsoid Arc.

Uplink Cell Capacity Class Value

M

INTEGER(1..100,…)

Value 1 shall indicate the minimum uplink cell capacity, and 100 shall indicate the maximum uplink cell capacity. . There should be linear relation between uplink cell capacity and Uplink Cell Capacity Class Value.

Downlink Cell Capacity Class Value

M

INTEGER(1..100,…)

Value 1 shall indicate the minimum downlink cell capacity, and 100 shall indicate the maximum downlink cell capacity. There should be linear relation between downlink cell capacity and Downlink Cell Capacity Class Value.

LAI

1

>PLMN Identity

M

9.2.2.189

>LAC

M

OCTET STRING (SIZE(2))

0000 and FFFE not allowed.

CI

M

OCTET STRING (SIZE(2))

C-ID

INTEGER

(0..65535)

Cell Individual Offset

INTEGER(-20..+20)

-20 -> -10dB

-19 -> -9.5dB

…

+20 -> +10dB

Cell Parameter ID

INTEGER(0..127,…)

CFN

INTEGER(0.. 255)

PLMN Identity

M

9.2.2.189

LAC

M

OCTET STRING (SIZE(2))

0000 and FFFE not allowed.

CN Domain Type

ENUMERATED(CS domain, PS domain, Don’t care,…)

See in TS 25.331 [16].

PLMN Identity

M

9.2.2.189

LAC

M

OCTET STRING (SIZE(2))

0000 and FFFE not allowed.

RAC

M

OCTET STRING (SIZE(1))

CHOICE Common Measurement Accuracy

M

>T_UTRAN-GPS Measurement Accuracy Class

>>T_UTRAN-GPS Measurement Accuracy Class

M

T_UTRAN-GPS Accuracy Class

9.2.1.59B

>T_UTRAN-GANSS Measurement Accuracy Class

>>T_UTRAN-GANSS Measurement Accuracy Class

M

T_UTRAN-GANSS Accuracy Class

9.2.1.112

Common Measurement Type

ENUMERATED(UTRAN GPS Timing of Cell Frames for UE Positioning ,

SFN-SFN Observed Time Difference, load, transmitted carrier power, received total wide band power, UL timeslot ISCP, …, RT Load,

NRT Load Information, UpPTS interference, UTRAN GANSS Timing of Cell Frames for UE Positioning)

UL timeslot ISCP shall only be used by TDD.

For measurements, which are requested on the Iur-g interface, only load, RT Load and NRT Load information are used.

“UpPTS interference” is used by 1.28Mcps TDD only

“UpPTS interference” means “UpPCH interference” in the whole 25.423, refer to TS 25.225 [14] and TS 25.224 [22].

CHOICE Common Measurement Value

M

–

>T_UTRAN-GPS Measurement Value Information

UTRAN only.

–

>>T_UTRAN-GPS Measurement Value Information

M

9.2.1.59D

–

>SFN-SFN Measurement Value Information

UTRAN only.

–

>>SFN-SFN Measurement Value Information

M

9.2.1.52C

–

>Load Value

–

>>Load Value

M

9.2.1.33A

–

>Transmitted Carrier Power Value

UTRAN only.

–

>>Transmitted Carrier Power Value

M

Transmitted Carrier Power 9.2.1.59A

–

>Received Total Wide Band Power Value

UTRAN only.

–

>>Received Total Wide Band Power Value

M

Received Total Wide Band Power 9.2.2.35A

–

>UL Timeslot ISCP Value

TDD Only.

–

>>UL Timeslot ISCP Value

M

UL Timeslot ISCP 9.2.3.13A

–

>Additional Common Measurement Values

–

>>RT Load Value

–

>>>RT Load Value

M

9.2.1.50B

YES

ignore

>>NRT Load Information Value

–

>>>NRT Load Information Value

M

9.2.1.41I

YES

ignore

>>UpPTS interference

1.28Mcps TDD Only.

–

>>>UpPTS interference Value

M

INTEGER (0..127,…)

According to mapping in TS 25.123 [24].

YES

reject

>>T_UTRAN-GANSS Measurement Value Information

UTRAN only.

–

>>>T_UTRAN-GANSS Measurement Value Information

M

9.2.1.114

YES

reject

CHOICE Measurement Availability

M

>Measurement Available

>>Common Measurement Value

M

9.2.1.12D

>Measurement not Available

NULL

Common Transport Channel Resources Initialisation Not Required

ENUMERATED(Not Required)

Coverage Indicator

ENUMERATED(Overlap, Covers, Contained in,…)

Procedure ID

0..1

Procedure ID is to be used if Criticality Diagnostics is part of Error Indication procedure, and not within the response message of the same procedure that caused the error.

–

>Procedure Code

M

INTEGER(0..255)

–

>Ddmode

M

ENUMERATED(FDD, TDD, Common)

Common = common to FDD and TDD. Common Ddmode is also applicable for Iur-g procedures listed in section 7.

–

Triggering Message

O

ENUMERATED(initiating message, successful outcome, unsuccessful outcome, outcome)

The Triggering Message is used only if the Criticality Diagnostics is part of Error Indication.

–

Procedure Criticality

O

ENUMERATED(reject, ignore, notify)

This Procedure Criticality is used for reporting the Criticality of the Triggering message

(Procedure).

–

Transaction ID

O

Transaction ID

–

Information Element Criticality Diagnostics

0..<maxNrOfErrors>

–

>IE Criticality

M

ENUMERATED(reject, ignore, notify)

The IE Criticality is used for reporting the criticality of the triggering IE. The value “Ignore” shall never be used.

–

>IE ID

M

INTEGER(0..65535)

The IE ID of the not understood or missing IE as defined in the ASN.1 part of the specification.

–

>Repetition Number

O

INTEGER(0..255)

The Repetition Number IE gives

● in case of a not understood IE:
The number of occurrences of the reported IE up to and including the not understood occurrence

● in case of a missing IE:
The number of occurrences up to but not including the missing occurrence.

Note: All the counted occurrences of the reported IE must have the same topdown hierarchical message structure of IEs with assigned criticality above them.

–

>Message Structure

O

9.2.1.39A

The Message Structure IE describes the structure in which the not understood or missing IE was detected.

This IE is included if the not understood IE is not the top level of the message.

YES

ignore

>Type of Error

M

ENUMERATED(not understood, missing, …)

YES

ignore

maxNrOfErrors

Maximum number of IE errors allowed to be reported with a single message.

C-RNTI

INTEGER(0..65535)

CHOICE CTFC Format

>2 bits long

>>CTFC value

M

INTEGER (0..3)

>4 bits long

>>CTFC value

M

INTEGER (0..15)

>6 bits long

>>CTFC value

M

INTEGER (0..63)

>8 bits long

>>CTFC value

M

INTEGER (0..255)

>12 bits long

>>CTFC value

M

INTEGER (0..4095)

>16 bits long

>>CTFC value

M

INTEGER (0..65535)

>max nb bits long

>>CTFC value

M

INTEGER (0..maxCTFC)

maxCTFC

Maximum number of the CTFC value is calculated according to the following:

with the notation according to TS 25.331 [16].

DCH ID

INTEGER

(0..255)

DCH Information Response

1..<maxNrOfDCHs>

Several DCHs belonging to the same set of coordinated DCHs may be included.

–

>DCH ID

M

9.2.1.16

–

>Binding ID

O

9.2.1.3

–

>Transport Layer Address

O

9.2.1.62

–

>Allowed Rate Information

O

9.2.1.2A

YES

ignore

>Transport Bearer Not Setup Indicator

O

9.2.2.4T

FDD Only.

YES

ignore

maxNrOfDCHs

Maximum number of DCHs for one UE.

Dedicated Measurement Type

ENUMERATED(SIR, SIR Error, Transmitted Code Power, RSCP, Rx Timing Deviation, Round Trip Time, …, Rx Timing Deviation LCR, Angle Of Arrival LCR,

HS-SICH Reception Quality, Rx Timing Deviation 768, Rx Timing Deviation 384 Extended, UE transmission power headroom, DL transport block size)

RSCP and HS-SICH Receptions Quality are used by TDD only, Rx Timing Deviation and Rx Timing Deviation 384 Extended are used by 3.84 Mcps TDD only, Rx Timing Deviation LCR is used by 1.28 TDD only,

Round Trip Time, SIR Error are used by FDD only.

Angle Of Arrival LCR is used by 1.28Mcps TDD only.

Rx Timing Deviation 768 is used by 7.68Mcps TDD only.

UE transmission power headroom is used by FDD, 1.28Mcps TDD, 3.84Mcps TDD and 7.68Mcps TDD.

“DL transport block size” is used by FDD only.

CHOICE Dedicated Measurement Value

M

–

>SIR Value

–

>>SIR Value

M

INTEGER(0..63)

According to mapping in TS 25.133 [23] and TS 25.123 [24].

–

>SIR Error Value

FDD Only

–

>>SIR Error Value

M

INTEGER(0..125)

According to mapping in TS 25.133 [23].

–

>Transmitted Code Power Value

–

>>Transmitted Code Power Value

M

INTEGER(0..127)

According to mapping in TS 25.133 [23] and TS 25.123 [24]

Values 0 to 9 and 123 to 127 shall not be used.

–

>RSCP

TDD Only.

–

>>RSCP

M

INTEGER(0..127)

According to mapping in TS 25.123 [24].

–

>Rx Timing Deviation Value

3.84Mcps TDD Only.

–

>>Rx Timing Deviation

M

INTEGER(0..8191)

According to mapping in TS 25.123 [24].

–

>Round Trip Time

FDD Only.

–

>>Round Trip Time

M

INTEGER(0..32767)

According to mapping in TS 25.133 [23].

–

>Additional Dedicated Measurement Values

–

>>Rx Timing Deviation Value LCR

1.28Mcps TDD Only.

YES

reject

>>>Rx Timing Deviation LCR

M

INTEGER(0..511)

According to mapping in TS 25.123 [24].

–

>>Angle of Arrival Value LCR

1.28Mcps TDD only.

YES

reject

>>>AOA LCR

M

INTEGER(0..719)

According to mapping in TS 25.123 [24].

–

>>>AOA LCR Accuracy Class

M

ENUMERATED(A, B, C, D, E, F, G, H,…)

According to mapping in TS 25.123 [24]

–

>>HS-SICH reception quality

Applicable to TDD only.

YES

reject

>>>HS-SICH reception quality Value

1

–

>>>>Failed HS-SICH

M

INTEGER (0..20)

According to mapping in TS 25.123 [24].

–

>>>>Missed HS-SICH

M

INTEGER (0..20)

According to mapping in TS 25.123 [24].

–

>>>>Total HS-SICH

M

INTEGER (0..20)

According to mapping in TS 25.123 [24].

–

>>Rx Timing Deviation Value 7.68Mcps

7.68Mcps TDD Only.

YES

reject

>>>Rx Timing Deviation 7.68Mcps

M

INTEGER(0..65535)

According to mapping in TS 25.123 [24].

–

>>Rx Timing Deviation Value 3.84Mcps Extended

3.84 Mcps TDD Only.

YES

reject

>>>Rx Timing Deviation 3.84Mcps Extended

M

INTEGER(0..32767)

According to mapping in TS 25.123 [24].

–

>>Extended Round Trip Time

FDD Only.

YES

ignore

>>>Extended Round Trip Time Value

M

INTEGER (32767..103041)

Continuation of intervals with step size as defined in TS 25.133 [23].

–

>>UE transmission power headroom

YES

reject

>>>UE transmission power headroom

M

INTEGER (0..31)

According to mapping in TS 25.133 [23] and TS 25.123 [24].

–

–

>>DL transport block size

FDD only.

>>>HS-DSCH Cell List

M

1.. <maxNrOfHSDSCH-1>

EACH

reject

>>>>HS-DSCH cell TBS

M

INTEGER (0.. 160000)

According to mapping of CQI in TS 25.214 [10]. See Note 1.

–

–

maxNrOfHSDSCH-1

Maximum number of HS-DSCH cells for one UE.

CHOICE Measurement Availability Indicator

M

–

>Measurement Available

–

>>Dedicated Measurement Value

M

9.2.1.19

–

>>CFN

O

9.2.1.9

Dedicated Measurement Time Reference.

_

>Measurement not Available

NULL

–

CHOICE Delayed Activation

M

>CFN

>>Activation CFN

M

CFN 9.2.1.7

>Separate Indication

NULL

CHOICE Delayed Activation Update

M

>Activate

>>CHOICE Activation Type

M

>>>Synchronised

>>>>Activation CFN

M

CFN 9.2.1.7

>>>Unsynchronised

NULL

>>Initial DL TX Power

M

DL Power

9.2.1.21

>>First RLS Indicator

O

9.2.2.16A

FDD Only.

>>Propagation Delay

O

9.2.2.33

FDD Only.

>>Extended Propagation Delay

O

9.2.2.33a

FDD Only.

>Deactivate

>>CHOICE Deactivation type

M

>>>Synchronised

>>>>Deactivation CFN

M

CFN 9.2.1.7

>>>Unsynchronised

NULL

GPS TOW

M

INTEGER(0..604799)

Time in seconds. This field indicates the baseline time for which the corrections are valid.

–

Status/Health

M

ENUMERATED

(UDRE scale 1.0, UDRE scale 0.75, UDRE scale 0.5, UDRE scale 0.3, UDRE scale 0.1, no data, invalid data)

This field indicates the status of the differential corrections.

–

Satellite DGPS Corrections Information

1..<maxNoSat>

–

>SatID

M

SAT ID

9.2.1.50A

–

>IODE

M

BIT STRING (SIZE(8))

This IE is the sequence number for the ephemeris for the particular satellite. It can be used to determine if new ephemeris is used for calculating the corrections that are provided. This eight-bit IE is incremented for each new set of ephemeris for the satellite and may occupy the numerical range of [0, 239] during normal operations.

–

>UDRE

M

ENUMERATED

(UDRE 1.0m,

1.0m <

UDRE 

4.0m,

4.0m <

UDRE 

8.0m,

8.0m <

UDRE,…)

User Differential Range Error. This field provides an estimate of the uncertainty (1-) in the corrections for the particular satellite. The value in this field shall be multiplied by the UDRE Scale Factor in the common Corrections Status/Health field to determine the final UDRE estimate for the particular satellite.

–

>PRC

M

INTEGER(

-2047..2047)

Scaling factor 0.32 meters.

–

>Range Correction Rate

M

INTEGER(-127.. 127)

Scaling factor 0.032 m/s.

–

>DGNSS Validity Period

O

9.2.1.138

YES

ignore

maxNoSat

Maximum number of satellites for which information can be provided.

Discard Timer

ENUMERATED (20, 40, 60, 80, 100, 120, 140, 160, 180, 200, 250, 300, 400, 500, 750, 1000, 1250, 1500, 1750, 2000, 2500, 3000, 3500, 4000, 4500, 5000, 7500, …)

Unit: ms

Diversity Control Field

ENUMERATED(May, Must, Must not,

…)

DL Power

INTEGER (-350..150)

Value = DL Power /10
Unit dB
Range –35.0 .. +15.0
Step 0.1dB

DPCH Constant Value

INTEGER (-10..10)

Unit dB
Granularity 1 dB.

D-RNTI

INTEGER(0..2^20 –1)

D-RNTI Release Indication

ENUMERATED(Release D‑RNTI, not Release D‑RNTI)

DRX Cycle Length Coefficient

INTEGER

(3..9)

Refers to ‘k’ in the formula as specified in TS 25.304 [15], Discontinuous Reception.

Extended GSM Cell Individual Offset

INTEGER (-50..-11 | 11..50)

Unit in dB. Step size is 1 dB.

FACH Flow Control Information

1..16

–

>FACH Scheduling Priority

M

Scheduling Priority Indicator 9.2.1.51A

–

>MAC-c/sh SDU Length

1..<maxNrOfMACcshSDU-Length>

–

>>MAC-c/sh SDU Length

M

9.2.1.34

–

>FACH Initial Window Size

M

9.2.1.27

–

maxNrOfMACcshSDU-Length

Maximum number of different MAC-c/sh SDU lengths.

FACH Initial Window Size

INTEGER(0..255)

Number of frames (MAC-c/sh SDUs).

255 = Unlimited number of FACH data frames.

FN reporting indicator

ENUMERATED(FN reporting required, FN reporting not required)

Frame Handling Priority

INTEGER

(0..15)

0=Lowest Priority,

…

15=Highest Priority.

Frame Offset

INTEGER

(0..255)

Frames.

Geographical Coordinates

M

9.2.1.30F

Uncertainty Code

M

INTEGER(

0..127)

The uncertainty “r” is derived from the “uncertainty code” k by

r = 10x(1.1^k-1).

Geographical Coordinates

M

9.2.1.30F

Uncertainty Ellipse

M

9.2.1.68A

Confidence

M

INTEGER(

0..127)

Geographical Coordinates

M

9.2.1.30F

Altitude and Direction

M

9.2.1.2B

Geographical Coordinates

M

9.2.1.30F

Altitude and Direction

M

9.2.1.2B

Uncertainty Ellipse

M

9.2.1.68A

Uncertainty Altitude

M

INTEGER(

0..127)

Confidence

M

INTEGER(

0..127)

Geographical Coordinates

M

9.2.1.30F

Inner radius

M

INTEGER(

0..2¹⁶-1)

The relation between the value (N) and the radius I in meters it describes is 5N r <5(N+1), except for N=2¹⁶-1 for which the range is extended to include all grater values of I.

Uncertainty radius

M

INTEGER(

0..127)

The uncertainty “r” is derived from the “uncertainty code” k by

r = 10x(1.1^k-1)

Offset angle

M

INTEGER(

0..179)

The relation between the value (N) and the angle (a) in degrees it describes is
2N a <2(N+1).

Included angle

M

INTEGER(

0..179)

The relation between the value (N) and the angle (a) in degrees it describes is
2N< a 2(N+1).

Confidence

M

INTEGER(

0..127)

Latitude Sign

M

ENUMERATED(North, South)

Degrees Of Latitude

M

INTEGER(

0..2²³-1)

The IE value (N) is derived by this formula:

N2²³ X /90  N+1

X being the latitude in degree (0°.. 90°).

Degrees Of Longitude

M

INTEGER(

-2²³..2²³-1)

The IE value (N) is derived by this formula:

N2²⁴ X /360  N+1

X being the longitude in degree (-180°..+180°).

GERAN Cell Capability

M

BIT STRING (SIZE(16))

Each bit indicates whether a cell supports a particular functionality or not. The value 1 of a bit indicates that the corresponding functionality is supported in a cell and value 0 indicates that the corresponding functionality is not supported in a cell. Each bit is defined as follows.

The first bit: A/Gb mode.

The second bit: Iu mode.

Note that undefined bits are considered as a spare bit and spare bits shall be set to 0 by the transmitter and shall be ignored by the receiver.

GERAN Classmark

M

OCTET STRING

Contents defined in TS 48.008 [38].

GERAN System Info

1..<maxNrOfGERANSI>

>GERAN System Info Block

M

OCTET STRING SIZE((1..23))

The first octet contains octet 1 of the GERAN system information block, the second octet contains octet 2 of the GERAN system information block and so on.

maxNrOfGERANSI

Maximum number of GERAN SI blocks that can be provided as part of NACC information.

WN_a

M

BIT STRING(8)

–

Satellite Almanac Information

M

1..<maxNrOfSatAlmanac-maxNoSat>

See Note 1.

–

>DataID

M

INTEGER
(0..3)

–

>SatID

M

SAT ID

9.2.1.50A

–

>e

M

BIT STRING(16)

–

>t_oa

M

BIT STRING(8)

–

>i

M

BIT STRING(16)

–

>OMEGADOT

M

BIT STRING(16)

–

>SV Health

M

BIT STRING(8)

–

>A^1/2

M

BIT STRING(24)

–

>OMEGA₀

M

BIT STRING(24)

–

>M₀

M

BIT STRING(24)

–

>

M

BIT STRING(24)

–

>af₀

M

BIT STRING(11)

–

>af₁

M

BIT STRING(11)

–

SV Global Health

O

BIT STRING (SIZE(364))

–

Complete Almanac Provided

O

BOOLEAN

This field indicates whether almanac is provided for the full GPS constellation or not. TRUE means complete GPS almanac is provided.

YES

ignore

maxNrOfSatAlmanac-maxNoSat

Maximum number of satellite almanacs for which information can be provided.

₀

M

BIT STRING (SIZE8))

₁

M

BIT STRING (SIZE(8))

₂

M

BIT STRING (SIZE(8))

₃

M

BIT STRING (SIZE(8))

₀

M

BIT STRING (SIZE(8))

₁

M

BIT STRING (SIZE(8))

₂

M

BIT STRING (SIZE(8))

₃

M

BIT STRING (SIZE(8))

Navigation Message 1to3

1..<maxNoSat>

>Transmission TOW

M

INTEGER0..1048575)

Time of the Week when the message is broadcast.

>SatID

M

SAT ID
9.2.1.50A

>TLM Message

M

BIT STRING (SIZE(14))

>Tlm Revd I

M

BIT STRING (SIZE(2)

>HO-Word

M

BIT STRING (SIZE(22))

>WN

M

BIT STRING (SIZE(10))

>C/A or P on L2

M

BIT STRING (SIZE(2))

>User Range Accuracy Index

M

BIT STRING (SIZE(4))

>SV Health

M

BIT STRING (SIZE(6))

>IODC

M

BIT STRING (SIZE(10))

>L2 P Data Flag

M

BIT STRING (SIZE(1))

>SF 1 Reserved

M

BIT STRING (SIZE(87))

>T_GD

M

BIT STRING (SIZE(8))

>t_oc

M

BIT STRING (SIZE(16))

>af₂

M

BIT STRING (SIZE(8))

>af₁

M

BIT STRING (SIZE(16))

>af₀

M

BIT STRING (SIZE(22))

>C_rs

M

BIT STRING (SIZE(16))

>n

M

BIT STRING (SIZE(16))

>M₀

M

BIT STRING (SIZE(32))

>C_uc

M

BIT STRING (SIZE(16))

>e

M

BIT STRING (SIZE(32))

>C_us

M

BIT STRING (SIZE(16))

>(A)^1/2

M

BIT STRING (SIZE(32))

>t_oe

M

BIT STRING (SIZE(16))

>Fit Interval Flag

M

BIT STRING (SIZE(1))

>AODO

M

BIT STRING (SIZE(5))

>C_ic

M

BIT STRING (SIZE(16))

>OMEGA₀

M

BIT STRING (SIZE(32))

>C_is

M

BIT STRING (SIZE(16))

>i₀

M

BIT STRING (SIZE(32))

>C_rc

M

BIT STRING (SIZE(16))

>

M

BIT STRING (SIZE(32))

>OMEGAdot

M

BIT STRING (SIZE(24))

>Idot

M

BIT STRING (SIZE(14))

>Spare/zero fill

M

BIT STRING (SIZE(20))

maxNoSat

Maximum number of satellites for which information can be provided.

CHOICE Bad Satellites Presence

M

>Bad Satellites

>>Satellite Information

1..<maxNoSat>

>>>BadSatID

M

SAT ID
9.2.1.50A

>No Bad Satellites

NULL

MaxNoSat

Maximum number of satellites for which information can be provided.

Geographical Coordinates

M

9.2.1.30F

Altitude and Direction

M

9.2.1.2B

A₁

M

BIT STRING (SIZE(24))

A₀

M

BIT STRING (SIZE(32))

t_ot

M

BIT STRING (SIZE(8))

t_LS

M

BIT STRING (SIZE(8))

WN_t

M

BIT STRING (SIZE(8))

WN_LSF

M

BIT STRING (SIZE(8))

DN

M

BIT STRING (SIZE(8))

t_LSF

M

BIT STRING (SIZE(8))

Guaranteed UL Rate

O

INTEGER(1..maxNrOfTFs)

“1”: TFI 0,

“2”: TFI 1,

“3”: TFI 2,

…

Guaranteed DL Rate

O

INTEGER(1..maxNrOfTFs)

“1”: TFI 0,

“2”: TFI 1,

“3”: TFI 2,

…

HCS Prio

INTEGER

(0..7)

0=Lowest Priority,

…

7=Highest Priority.

HS-DSCH MAC-d Flow Specific Information

0..<maxNrOfMACdFlows>

–

>HS-DSCH MAC-d Flow ID

M

9.2.1.30O

–

>Allocation/Retention Priority

O

9.2.1.1

–

>Transport Bearer Request Indicator

M

9.2.1.61

–

>Traffic Class

O

9.2.1.58A

–

>Binding ID

O

9.2.1.3

Shall be ignored if bearer establishment with ALCAP.

–

>Transport Layer Address

O

9.2.1.62

Shall be ignored if bearer establishment with ALCAP.

–

>TNL QoS

O

9.2.1.56A

Shall be ignored if bearer establishment with ALCAP.

YES

ignore

Priority Queue Information

0..<maxNrOfPrioQueues>

–

>Priority Queue ID

M

9.2.1.45A

–

>Scheduling Priority Indicator

O

9.2.1.51A

–

>Discard Timer

O

9.2.1.19C

–

>MAC-hs Guaranteed Bit Rate

O

9.2.1.34Aa

–

CQI Power Offset

O

9.2.2.24b

For FDD only.

–

ACK Power Offset

O

9.2.2.b

For FDD only.

–

NACK Power Offset

O

9.2.2.26a

For FDD only.

–

HS-SCCH Power Offset

O

9.2.2.19d

For FDD only.

–

TDD ACK NACK Power Offset

O

9.2.3.7I

For TDD only.

–

HARQ Preamble Mode

O

9.2.2.57

For FDD only.

YES

ignore

MIMO Mode Indicator

O

9.2.1.135

For FDD and 1.28Mcps TDD only.

YES

reject

Sixtyfour QAM Usage Allowed Indicator

O

9.2.2.79A

For FDD only.

YES

ignore

Enhanced HS Serving CC Abort

O

ENUMERATED (Abort Enhanced HS Serving CC, …)

For FDD only.

YES

reject

UE Support Indicator Extension

O

9.2.2.103

YES

ignore

Power Offset For S-CPICH for MIMO Request Indicator

O

9.2.2.105

For FDD only.

YES

ignore

Single Stream MIMO Mode Indicator

O

9.2.2.107

For FDD only.

YES

reject

MIMO with four transmit antennas Mode Indicator

O

9.2.2.146

For FDD only

YES

reject

Dual Stream MIMO with four transmit antennas Mode Indicator

O

9.2.2.150

For FDD only

YES

reject

Power Offset For S-CPICH for MIMO with four transmit antennas Request Indicator

O

9.2.2.147

For FDD only

YES

ignore

Multiflow Reconfiguration

O

9.2.2.151

For FDD only

YES

reject

maxNrOfMACdFlows

Maximum number of HS-DSCH MAC-d flows.

maxNrOfPrioQueues

Maximum number of Priority Queues.

HS-DSCH Initial Capacity Allocation

1..< maxNrOfPrioQueues>

–

>Scheduling Priority Indicator

M

9.2.1.51A

–

>Maximum MAC-d PDU Size

M

MAC-d PDU Size 9.2.1.34A

Shall be ignored if Maximum MAC-d PDU Size Extended IE is present.

–

>HS-DSCH Initial Window Size

M

9.2.1.30Nb

–

>Maximum MAC-d PDU Size Extended

O

MAC PDU Size Extended

9.2.1.34D

YES

ignore

maxNrOfPrioQueues

Maximum number of Priority Queues.

HS-DSCH Initial Window Size

INTEGER (1..255)

Number of MAC-d PDUs

If HS-DSCH MAC-d PDU Size Format = “Flexible MAC-d PDU Size” the credit shall be determined in octets:

credit (in octets) = Maximum MAC-d PDU Size extended * HS-DSCH Initial Window Size.

HS-DSCH MAC-d Flow ID

INTEGER

(0..7)

HS-DSCH MAC-d Flow Specific Information

1..<maxNrOfMACdFlows>

–

>HS-DSCH MAC-d Flow ID

M

9.2.1.30O

–

>Allocation/Retention Priority

M

9.2.1.1

–

>Traffic Class

M

9.2.1.58A

–

>Binding ID

O

9.2.1.3

Shall be ignored if bearer establishment with ALCAP.

–

>Transport Layer Address

O

9.2.1.62

Shall be ignored if bearer establishment with ALCAP.

–

>TNL QoS

O

9.2.1.56A

Shall be ignored if bearer establishment with ALCAP.

YES

ignore

>TrCH Source Statistics Descriptor

O

9.2.1.65

YES

ignore

Priority Queue Information

1..<maxNrOfPrioQueues>

–

>Priority Queue ID

M

9.2.1.45A

–

>Associated HS-DSCH MAC-d Flow

M

HS-DSCH MAC-d Flow ID

9.2.1.30O

The HS-DSCH MAC-d Flow ID shall be one of the flow IDs defined in the HS-DSCH MAC-d Flow Specific Information of this IE.

Multiple Priority Queues can be associated with the same HS-DSCH MAC-d Flow ID.

–

>Scheduling Priority Indicator

M

9.2.1.51A

–

>T1

M

9.2.1.54A

–

>Discard Timer

O

9.2.1.19C

–

>MAC-hs Window Size

M

9.2.1.34C

–

>MAC-hs Guaranteed Bit Rate

O

9.2.1.34Aa

–

>MAC-d PDU Size Index

1..<maxNrOfPDUIndexes>

–

>>SID

M

9.2.1.52D

Shall be ignored if Maximum MAC-d PDU Size extended IE is present.

–

>>MAC-d PDU Size

M

9.2.1.34A

Shall be ignored if Maximum MAC-d PDU Size extended IE is present.

–

>RLC Mode

M

9.2.1.48D

–

>Maximum MAC-d PDU Size extended

O

MAC PDU Size Extended

9.2.1.34D

YES

reject

>DL RLC PDU Size Format

O

9.2.1.136

YES

ignore

>UE Aggregate Maximum Bit Rate Enforcement Indicator

O

NULL

YES

ignore

maxNrOfMACdFlows

Maximum number of HS-DSCH MAC-d flows.

maxNrOfPrioQueues

Maximum number of Priority Queues.

maxNrOfPDUIndexes

Maximum number of different MAC-d PDU SIDs.

HS-DSCH MAC-d Flows To Delete

1..<maxNrOfMACdFlows>

>HS-DSCH MAC-d Flow ID

M

9.2.1.30O

maxNrOfMACdFlows

Maximum number of HS-DSCH MAC-d flows.

HS-DSCH MAC-d PDU Size Format

ENUMERATED (Indexed MAC-d PDU Size, Flexible MAC-d PDU Size)

HS-DSCH Physical Layer Category

INTEGER (1..64,…)

HS-DSCH-RNTI

INTEGER

(0..65535)

HS-DSCH MAC-d Flow Specific Information

0..<maxNrOfMACdFlows>

–

>HS-DSCH MAC-d Flow ID

M

9.2.1.30O

–

>Allocation/Retention Priority

O

9.2.1.1

–

>Transport Bearer Request Indicator

M

9.2.1.61

–

>Traffic Class

O

9.2.1.58A

–

>Binding ID

O

9.2.1.3

Shall be ignored if bearer establishment with ALCAP.

–

>Transport Layer Address

O

9.2.1.62

Shall be ignored if bearer establishment with ALCAP.

–

>TNL QoS

O

9.2.1.56A

Shall be ignored if bearer establishment with ALCAP.

YES

ignore

Priority Queue Information

0..<maxNrOfPrioQueues>

–

>CHOICE Priority Queue

M

–

>>Add Priority Queue

–

>>>Priority Queue ID

M

9.2.1.45A

–

>>>Associated HS-DSCH MAC-d Flow

M

HS-DSCH MAC-d Flow ID 9.2.1.30O

Shall only refer to a HS-DSCH MAC-d flow already existing in the old configuration.

Multiple Priority Queues can be associated with the same HS-DSCH MAC-d Flow ID.

–

>>>Scheduling Priority Indicator

M

9.2.1.51A

–

>>>T1

M

9.2.1.54A

–

>>>Discard Timer

O

9.2.1.19C

–

>>>MAC-hs Window Size

M

9.2.1.34C

–

>>>MAC-hs Guaranteed Bit Rate

O

9.2.1.34Aa

–

>>>MAC-d PDU Size Index

1..<maxNrOfPDUIndexes>

–

>>>>SID

M

9.2.1.52D

Shall be ignored if Maximum MAC-d PDU Size extended IE is present.

–

>>>>MAC-d PDU Size

M

9.2.1.34A

Shall be ignored if Maximum MAC-d PDU Size extended IE is present.

–

>>>RLC Mode

M

9.2.1.48D

–

>>>Maximum MAC-d PDU Size extended

O

MAC PDU Size Extended

9.2.1.34D

YES

reject

>>>DL RLC PDU Size Format

O

9.2.1.136

YES

ignore

>>Modify Priority Queue

–

>>>Priority Queue ID

M

9.2.1.45A

Shall only refer to a Priority Queue already existing in the old configuration.

–

>>>Scheduling Priority Indicator

O

9.2.1.51A

–

>>>T1

O

9.2.1.54A

–

>>>Discard Timer

O

9.2.1.19C

–

>>>MAC-hs Window Size

O

9.2.1.34C

–

>>>MAC-hs Guaranteed Bit Rate

O

9.2.1.34Aa

–

>>>MAC-d PDU Size Index

0..<maxNrOfPDUIndexes>

–

>>>>SID

M

9.2.1.52D

Shall be ignored if Maximum MAC-d PDU Size extended IE is present.

–

>>>>MAC-d PDU Size

M

9.2.1.34A

Shall be ignored if Maximum MAC-d PDU Size extended IE is present.

–

>>>Maximum MAC-d PDU Size extended

O

MAC PDU Size Extended

9.2.1.34D

YES

reject

>>>DL RLC PDU Size Format

O

9.2.1.136

YES

ignore

>>Delete Priority Queue

–

>>>Priority Queue ID

M

9.2.1.45A

Shall only refer to a Priority Queue already existing in the old configuration.

–

MAC-hs Reordering Buffer Size for RLC-UM

O

9.2.1.34Ab

–

CQI Feedback Cycle k

O

9.2.2.24a

For FDD only.

–

CQI Repetition Factor

O

9.2.2.24c

For FDD only.

–

ACK-NACK Repetition Factor

O

9.2.2.a

For FDD only.

–

CQI Power Offset

O

9.2.2.24b

For FDD only.

–

ACK Power Offset

O

9.2.2.b

For FDD only.

–

NACK Power Offset

O

9.2.2.26a

For FDD only.

–

HS-SCCH Power Offset

O

9.2.2.19d

For FDD only.

–

HS-SCCH Code Change Grant

O

9.2.1.30S

–

TDD ACK NACK Power Offset

O

9.2.3.7I

For TDD only.

–

HARQ Preamble Mode

O

9.2.2.57

For FDD only.

YES

ignore

HS-PDSCH Code Change Grant

O

9.2.1.30W

For FDD only.

YES

ignore

MIMO Mode Indicator

O

9.2.1.135

For FDD and 1.28Mcps TDD only.

YES

reject

HS-DSCH MAC-d PDU Size Format

O

9.2.1.30OC

YES

reject

Sixtyfour QAM Usage Allowed Indicator

O

9.2.2.79A

For FDD only.

YES

ignore

UE Capabilities Information

O

YES

ignore

>HS-DSCH Physical Layer Category

M

9.2.1.30Oa

–

>1.28 Mcps TDD uplink physical channel capability

O

9.2.3.10D

Applicable to 1.28Mcps TDD only.

YES

ignore

>Number of Supported Carriers

O

ENUMERATED (

One-one carrier, One-three carrier, Three-three carrier, One-six carrier,

Tree-six carrier,

Six-six carrier, …, One-Two carrier Discontiguous, Two-Two carrier Discontiguous, One-Two carrier Contiguous, Two-Two carrier Contiguous)

Applicable to 1.28Mcps TDD only

This IE indicates the number of carrier that UE can support at the same time,where “ One-three carrier” means the number of supported carrier is one for the uplink,and three for the downlink.

One-Two carrier Discontiguous and Two-Two carrier Discontiguous mean that the UE is capable of supporting two non-adjacent carriers.

One-Two carrier Contiguous and Two-Two carrier Contiguous mean that the UE is only capable of supporting two adjacent carriers.

YES

reject

>MIMO SF Mode Supported For HS-PDSCH dual stream

O

ENUMERATED (SF1, SF1/SF16)

Applicable to 1.28Mcps TDD only.

YES

ignore

>Multi-carrier HS-DSCH Physical Layer Category

O

HS-DSCH Physical Layer Category

9.2.1.30Oa

Applicable to 1.28Mcps TDD only.

YES

ignore

>UE TS0 Capability LCR

O

ENUMERATED (TS0 Capable, TS0 Non-Capable)

Applicable to 1.28Mcps TDD only.

YES

ignore

>UE RF Band Capability LCR

C-NofSupportedCarriers

9.2.3.84

Applicable to 1.28Mcps TDD only.

YES

ignore

Enhanced HS Serving CC Abort

O

ENUMERATED (Abort Enhanced HS Serving CC, …)

For FDD only.

YES

reject

UE Support Indicator Extension

O

9.2.2.103

YES

ignore

Power Offset For S-CPICH for MIMO Request Indicator

O

9.2.2.105

For FDD only.

YES

ignore

Single Stream MIMO Mode Indicator

O

9.2.2.107

For FDD only.

YES

reject

MIMO with four transmit antennas Mode Indicator

O

9.2.2.146

For FDD only

YES

reject

Dual Stream MIMO with four transmit antennas Mode Indicator

O

9.2.2.150

For FDD only

YES

reject

Power Offset For S-CPICH for MIMO with four transmit antennas Request Indicator

O

9.2.2.147

For FDD only

YES

ignore

Multiflow Reconfiguration

O

9.2.2.151

For FDD only

YES

reject

CQI Feedback Cycle2 k

O

CQI Feedback Cycle k2

9.2.2.181

For FDD only

YES

ignore

CQI Cycle Switch Timer

O

ENUMERATED (v4, v8, v16, v32, v64, v128, v256, v512, Infinity)

For FDD only, refer to TS 25.331 [16].

YES

ignore

NofSupportedCarriers

This IE shall be present if the Number of Supported Carriers IE is equal to "One-Two carrier Discontiguous" or "Two-Two carrier Discontiguous" and the concerned cell and the UE support more than one RF band.

maxNrOfMACdFlows

Maximum number of MAC-d flows.

maxNrOfPrioQueues

Maximum number of Priority Queues.

maxNrOfPDUIndexes

Maximum number of MAC-d PDU Size Indexes (SIDs).

HS-SCCH Code Change Indicator

ENUMERATED (HS-SCCH Code Change needed)

HS-SCCH Code Change Grant

ENUMERATED(Change Granted)

IMEI

OCTET STRING (SIZE (8))

– hexadecimal digits 0 to F, two hexadecimal digits per octet,

– each hexadecimal digit encoded 0000 to 1111,

– 1111 used as filler for bits 8 to 5 of last octet.

– bit 4 to 1 of octet n encoding digit 2n-1.

– bit 8 to 5 of octet n encoding digit 2n.

Number of hexadecimal digits shall be 15.

IMEISV

OCTET STRING (SIZE (8))

– hexadecimal digits 0 to F, two hexadecimal digits per octet,

– each hexadecimal digit encoded 0000 to 1111,

– 1111 used as filler for bits 8 to 5 of last octet.

– bit 4 to 1 of octet n encoding digit 2n-1.

– bit 8 to 5 of octet n encoding digit 2n.

Number of hexadecimal digits shall be 16.

HS-PDSCH Code Change Indicator

ENUMERATED (HS-PDSCH Code Change needed)

HS-PDSCH Code Change Grant

ENUMERATED(Change Granted)

IMSI

OCTET STRING

(SIZE(3..8))

-Decimal digits coded in BCD.

-“1111” used as filler.

-bit 4 to 1 of octet n is encoding digit 2n-1.

-bit 8 to 5 of octet n is encoding digit 2n.

Information Exchange ID

M

INTEGER(0 .. 2^20-1)

CHOICE Information Report Characteristics Type

M

>On Demand

NULL

>Periodic

>>CHOICE Information Report Periodicity Scale

M

The frequency with which the Node B shall send information reports.

>>>minute

>>>>Report Periodicity Value

M

INTEGER (1..60,…)

>>>hour

>>>>Report Periodicity Value

M

INTEGER (1..24,…)

>On Modification

>>Information Threshold

O

9.2.1.31D

CHOICE Information Type Item

M

–

>DGPS Corrections

>>PRC Deviation

M

ENUMERATED(1, 2, 5, 10, …)

PRC deviation in meters from the previously reported value, which shall trigger a report.

–

>DGANSS

>>PRC Deviation

M

ENUMERATED

(1, 2, 5, 10, …)

PRC deviation in meters from the previously reported value, which shall trigger a report.

–

Information Type Item

M

ENUMERATED

(UTRAN Access Point Position with Altitude, UTRAN Access Point Position,

IPDL Parameters,

GPS Information,

DGPS Corrections,

GPS RX Pos, SFN-SFN Measurement Reference Point Position,…, Cell Capacity Class, NACC Related Data, MBMS Bearer Service Full Address, Inter-frequency Cell Information, GANSS Information, DGANSS Corrections, GANSS RX Pos, MBMS Counting Information, MBMS Transmission Mode, MBMS Neighbouring Cell Information, MBMS RLC Sequence Number, ANR Cell Information, Common E-RGCH Cell Information)

For information exchange on the Iur-g interface, only the Cell Capacity Class is used.

MBMS Counting Information, MBMS Transmission Mode, MBMS Neighbouring Cell Information and MBMS RLC Sequence Numbe shall only be used by FDD.

–

GPS Information

C-GPS

1..<maxNoGPSTypes>

–

>GPS Information Item

ENUMERATED

(GPS Navigation Model and Time Recovery,

GPS Ionospheric Model,

GPS UTC Model,

GPS Almanac,

GPS Real-Time Integrity,

…)

–

GANSS Information

C-GANSS

YES

ignore

>GANSS Common Data