6 Measurements for UTRA FDD
25.2153GPPMeasurements (FDD)Physical layerRelease 17TS
6.1 UE measurements
6.1.1 Compressed mode
6.1.1.1 Use of compressed mode for monitoring
On command from the UTRAN, a UE shall monitor cells on other FDD frequencies and on other modes and radio access technologies that are supported by the UE (i.e. TDD, GSM, E-UTRA). To allow the UE to perform measurements, UTRAN shall command that the UE enters in compressed mode, depending on the UE capabilities.
The UE capabilities define whether a UE requires compressed mode in order to monitor cells on other FDD frequencies and on other modes and radio access technologies. UE capabilities indicate the need for compressed mode separately for the uplink and downlink and for each mode, radio access technology and frequency band.
A UE shall support compressed mode for all cases for which the UE indicates that compressed mode is required.
A UE does not need to support compressed mode for cases for which the UE indicates that compressed mode is not required. For these cases, the UE shall support an alternative means of making the measurements.
The UE shall support one single measurement purpose for one transmission gap pattern sequence. The measurement purpose of the transmission gap pattern sequence is signalled by higher layers.
The following subclause provides rules to parameterise the compressed mode.
6.1.1.2 Parameterisation of the compressed mode
In response to a request from higher layers, the UTRAN shall signal to the UE the compressed mode parameters.
A transmission gap pattern sequence consists of consecutive occurrences of transmission gap pattern 1, where transmission gap pattern 1 consists of one or two transmission gaps. See figure 1.
The following parameters characterise a transmission gap pattern:
– TGSN (Transmission Gap Starting Slot Number): A transmission gap pattern begins in a radio frame, henceforward called first radio frame of the transmission gap pattern, containing at least one transmission gap slot. TGSN is the slot number of the first transmission gap slot within the first radio frame of the transmission gap pattern;
– TGL1 (Transmission Gap Length 1): This is the duration of the first transmission gap within the transmission gap pattern, expressed in number of slots;
– TGL2 (Transmission Gap Length 2): This is the duration of the second transmission gap within the transmission gap pattern, expressed in number of slots. If this parameter is not explicitly set by higher layers, then TGL2 = TGL1;
– TGD (Transmission Gap start Distance): This is the duration between the starting slots of two consecutive transmission gaps within a transmission gap pattern, expressed in number of slots. The resulting position of the second transmission gap within its radio frame(s) shall comply with the limitations of [2]. If this parameter is not set by higher layers, then there is only one transmission gap in the transmission gap pattern;
– TGPL1 (Transmission Gap Pattern Length): This is the duration of transmission gap pattern 1, expressed in number of frames;
The following parameters control the transmission gap pattern sequence start and repetition:
– TGPRC (Transmission Gap Pattern Repetition Count): This is the number of transmission gap patterns within the transmission gap pattern sequence;
– TGCFN (Transmission Gap Connection Frame Number): This is the CFN of the first radio frame of the first pattern 1 within the transmission gap pattern sequence.
In addition to the parameters defining the positions of transmission gaps, each transmission gap pattern sequence is characterised by:
– UL/DL compressed mode selection: This parameter specifies whether compressed mode is used in UL only, DL only or both UL and DL;
– UL compressed mode method: The methods for generating the uplink compressed mode gap are spreading factor division by two or higher layer scheduling and are described in [2]. This parameter does not impact the compressed mode method used when DL_DCH_FET_Config is configured by higher layers;
– DL compressed mode method: The methods for generating the downlink compressed mode gap are spreading factor division by two or higher layer scheduling and are described in [2]. This parameter does not impact the compressed mode method used when DL_DCH_FET_Config is configured by higher layers;
– downlink frame type: This parameter defines if frame structure type ‘A’ or ‘B’ shall be used in downlink compressed mode. The frame structures are defined in [2];
– scrambling code change: This parameter indicates whether the alternative scrambling code is used for compressed mode method ‘SF/2’. Alternative scrambling codes are described in [3];
– RPP: Recovery Period Power control mode specifies the uplink power control algorithm applied during recovery period after each transmission gap in compressed mode. RPP can take 2 values (0 or 1). The different power control modes are described in [4];
– ITP: Initial Transmit Power mode selects the uplink power control method to calculate the initial transmit power after the gap. ITP can take two values (0 or 1) and is described in [4].
The UE shall support simultaneous compressed mode pattern sequences which can be used for different measurements. The following measurement purposes can be signalled from higher layers:
– FDD
– TDD
– GSM carrier RSSI measurement
– Initial BSIC identification
– BSIC re-confirmation
– E-UTRA.
The UE shall support one compressed mode pattern sequence for each measurement purpose while operating in FDD mode, assuming the UE needs compressed mode to perform the respective measurement. In case the UE supports several of the measurement purposes, it shall support in parallel one compressed mode pattern sequence for each supported measurement purpose where the UE needs compressed mode to perform the measurement. The capability of the UE to operate in compressed mode in uplink and downlink is given from the UE capabilities.
The GSM measurements Initial BSIC identification and BSIC re-confirmation are defined in [20].
Higher layers will ensure that the compressed mode gaps do not overlap and are not scheduled to overlap the same frame. The behaviour when an overlap occurs is described in [11]. UE is not required to support two compressed mode gaps in a frame.
In all cases, higher layers have control of individual UE parameters. Any pattern sequence can be stopped on higher layers’ command.
The parameters TGSN, TGL1, TGL2, TGD, TGPL1, TGPRC and TGCFN shall all be integers.
Figure 1: Illustration of compressed mode pattern parameters
Annex A (informative):
Change history
Change history |
|||||||
---|---|---|---|---|---|---|---|
Date |
TSG # |
TSG Doc. |
CR |
Rev |
Subject/Comment |
Old |
New |
14/01/00 |
RAN_05 |
RP-99590 |
– |
Approved at TSG RAN #5 and placed under Change Control |
– |
3.0.0 |
|
14/01/00 |
RAN_06 |
RP-99688 |
001 |
3 |
Clarifications for compressed mode parameters |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99689 |
002 |
– |
Definition of PCCPCH RSCP |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99689 |
003 |
– |
Definition of observed time difference to GSM cell |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99688 |
004 |
– |
Measurements are done on Primary CPICH |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99689 |
005 |
1 |
Physical channel BER on DPCCH |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99688 |
006 |
– |
Definition of SIR measurement |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99689 |
007 |
2 |
Ranges and resolution of timing measurements |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99688 |
009 |
2 |
Range and resolution for RF related measurements |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99689 |
010 |
2 |
New subclauses: 5.1.15 – UE GPS Timing of Cell Frames for LCS; 5.2.8 UTRAN GPS Timing of Cell Frames for LCS |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99688 |
011 |
– |
Removal of Annex A from TS 25.215 |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99688 |
013 |
– |
Definition of Transmitted code power |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99688 |
014 |
2 |
Range and resolution of BLER measurements |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99688 |
015 |
2 |
Range and resolution of BER measurements |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99688 |
020 |
– |
Correction of SFN-SFN observed time difference |
3.0.0 |
3.1.0 |
14/01/00 |
RAN_06 |
RP-99688 |
021 |
1 |
CFN-SFN measurement with compressed mode |
3.0.0 |
3.1.0 |
14/01/00 |
– |
– |
– |
Change history was added by the editor |
3.1.0 |
3.1.1 |
|
31/03/00 |
RAN_07 |
RP-000066 |
024 |
1 |
Definition of Transmitted carrier power |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
025 |
– |
Clarification of Observed time difference to GSM cell |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
027 |
– |
Naming of BER/BLER mapping |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
028 |
– |
Minor corrections in TS 25.215 |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
029 |
– |
Re-definition of timing measurements |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
030 |
2 |
Mapping of timing measurements |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
031 |
– |
Removal of note in Round trip time measurement |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
033 |
– |
Removal of fixed gap position in 25.215 |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
036 |
4 |
Corrections to 25.215 compressed mode parameter list |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
037 |
3 |
Definition and range of physical channel BER |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
040 |
– |
Clarification of CPICH measurements in Tx diversity |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
042 |
1 |
UTRAN RSSI measurement |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
043 |
1 |
UTRAN Propagation delay |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
044 |
2 |
Correction to subclauses: 5.1.15 UE GPS Timing of Cell Frames for LCS; 5.2.8 UTRAN GPS Timing of Cell Frames for LCS, including timing mapping |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
047 |
– |
Removal of RSCP measurement |
3.1.1 |
3.2.0 |
31/03/00 |
RAN_07 |
RP-000066 |
048 |
– |
UE BER measurement removal and clarification for use of uplink compressed mode |
3.1.1 |
3.2.0 |
26/06/00 |
RAN_08 |
RP-000270 |
049 |
1 |
Propagation delay for PCPCH |
3.2.0 |
3.3.0 |
26/06/00 |
RAN_08 |
RP-000270 |
050 |
1 |
Maximum number of simultaneous compressed mode pattern sequences |
3.2.0 |
3.3.0 |
26/06/00 |
RAN_08 |
RP-000270 |
051 |
1 |
Clarification of Physical channel BER |
3.2.0 |
3.3.0 |
26/06/00 |
RAN_08 |
RP-000270 |
052 |
– |
Clarification of transmitted code power |
3.2.0 |
3.3.0 |
26/06/00 |
RAN_08 |
RP-000270 |
053 |
– |
Editorial correction in TS 25.215 |
3.2.0 |
3.3.0 |
26/06/00 |
RAN_08 |
RP-000270 |
055 |
– |
Proposed CR for Measurements of RACH in FDD |
3.2.0 |
3.3.0 |
26/06/00 |
RAN_08 |
RP-000270 |
056 |
– |
Proposed CR for Measurements of CPCH in FDD |
3.2.0 |
3.3.0 |
26/06/00 |
RAN_08 |
RP-000270 |
057 |
– |
Transfer of information from TS 25.212 table 9 to TS 25.215 |
3.2.0 |
3.3.0 |
26/06/00 |
RAN_08 |
RP-000270 |
058 |
– |
Correction to CM parameter list |
3.2.0 |
3.3.0 |
26/06/00 |
RAN_08 |
RP-000270 |
062 |
– |
Clarification of radio link measurements in compressed mode |
3.2.0 |
3.3.0 |
26/06/00 |
RAN_08 |
RP-000270 |
063 |
– |
Clarification of the Transmitted code power measurement in Tx diversity |
3.2.0 |
3.3.0 |
26/06/00 |
RAN_08 |
RP-000270 |
064 |
1 |
Removal of Range/mapping |
3.2.0 |
3.3.0 |
26/06/00 |
RAN_08 |
RP-000270 |
066 |
– |
Removal of UTRAN TrCH BLER measurement |
3.2.0 |
3.3.0 |
23/09/00 |
RAN_09 |
RP-000343 |
067 |
– |
Insertion of UTRAN SIRerro measurement in 25.215 |
3.3.0 |
3.4.0 |
23/09/00 |
RAN_09 |
RP-000343 |
068 |
– |
Reporting of UTRAN Transmitted carrier power |
3.3.0 |
3.4.0 |
23/09/00 |
RAN_09 |
RP-000343 |
070 |
– |
Clarification of UTRAN SIR measurement |
3.3.0 |
3.4.0 |
23/09/00 |
RAN_09 |
RP-000343 |
071 |
– |
Clarification of first significant path |
3.3.0 |
3.4.0 |
23/09/00 |
RAN_09 |
RP-000343 |
072 |
– |
Clarification of radio link set as the measured object |
3.3.0 |
3.4.0 |
15/12/00 |
RAN_10 |
RP-000541 |
069 |
3 |
Support of parallel compressed mode patterns |
3.4.0 |
3.5.0 |
15/12/00 |
RAN_10 |
RP-000541 |
074 |
1 |
Clarification of SIRerror measurement during compressed mode |
3.4.0 |
3.5.0 |
15/12/00 |
RAN_10 |
RP-000541 |
075 |
2 |
Definition of UTRAN RSSI |
3.4.0 |
3.5.0 |
15/12/00 |
RAN_10 |
RP-000541 |
076 |
1 |
Clarification of GPS timing measurements |
3.4.0 |
3.5.0 |
15/12/00 |
RAN_10 |
RP-000541 |
077 |
2 |
Clarification of reference point for UE/UTRAN measurements |
3.4.0 |
3.5.0 |
15/12/00 |
RAN_10 |
RP-000541 |
078 |
1 |
Correction to measurement "Rx-Tx time difference" |
3.4.0 |
3.5.0 |
15/12/00 |
RAN_10 |
RP-000541 |
080 |
1 |
Clarifications to compressed mode usage |
3.4.0 |
3.5.0 |
16/03/01 |
RAN_11 |
– |
– |
– |
Approved as Release 4 specification (v4.0.0) at TSG RAN #11 |
3.5.0 |
4.0.0 |
16/03/01 |
RAN_11 |
RP-010061 |
079 |
2 |
Correction of the observed time difference to GSM measurement |
3.5.0 |
3.6.0 |
16/03/01 |
RAN_11 |
RP-010061 |
081 |
– |
Removal of UE SIR measurement |
3.5.0 |
3.6.0 |
16/03/01 |
RAN_11 |
RP-010061 |
082 |
1 |
Correction of GSM reference |
3.5.0 |
3.6.0 |
16/03/01 |
RAN_11 |
RP-010061 |
083 |
– |
Correction of GPS Timing measurement |
3.5.0 |
3.6.0 |
16/03/01 |
RAN_11 |
RP-010061 |
086 |
– |
Correction on transport channel BLER |
3.5.0 |
3.6.0 |
16/03/01 |
RAN_11 |
RP-010072 |
085 |
– |
RTD measurement in UTRAN for FDD |
3.5.0 |
4.0.0 |
15/06/01 |
RAN_12 |
RP-010335 |
088 |
– |
Renaming of LCS measurements |
4.0.0 |
4.1.0 |
15/06/01 |
RAN_12 |
RP-010456 |
090 |
2 |
Correction the TrCH BLER measurement |
4.0.0 |
4.1.0 |
21/09/01 |
RAN_13 |
RP-010521 |
096 |
– |
Removal of the BLER measurement of the BCH |
4.1.0 |
4.2.0 |
14/12/01 |
RAN_14 |
RP-010740 |
098 |
– |
Clarification of internal measurements |
4.2.0 |
4.3.0 |
14/12/01 |
RAN_14 |
RP-010740 |
103 |
– |
Clarification of P-CCPCH RSCP in 25.215 |
4.2.0 |
4.3.0 |
14/12/01 |
RAN_14 |
RP-010740 |
105 |
– |
Revised definitions of CPICH Ec/No and UTRA carrier RSSI |
4.2.0 |
4.3.0 |
14/12/01 |
RAN_14 |
RP-010745 |
099 |
2 |
UE GPS code phase measurement |
4.2.0 |
4.3.0 |
14/12/01 |
RAN_14 |
RP-010745 |
106 |
1 |
UTRAN SFN-SFN observed time difference measurement |
4.2.0 |
4.3.0 |
08/03/02 |
RAN_15 |
RP-020245 |
114 |
3 |
Clarification of UE measurements Applicability |
4.3.0 |
4.4.0 |
08/03/02 |
RAN_15 |
RP-020048 |
116 |
– |
Correction to the definition of UTRAN GPS timing of cell frames for UE positioning |
4.3.0 |
4.4.0 |
08/03/02 |
RAN_15 |
RP-020048 |
117 |
– |
Correction to the definition of UE GPS timing of cell frames for UE positioning |
4.3.0 |
4.4.0 |
08/03/02 |
RAN_15 |
RP-020231 |
111 |
1 |
Removal of channel coding option "no coding" for FDD |
4.3.0 |
4.4.0 |
08/03/02 |
RAN_15 |
– |
– |
– |
Raised up to v5.0.0 together with other specs. |
4.4.0 |
5.0.0 |
18/09/02 |
RAN_17 |
RP-020530 |
119 |
4 |
Transmitted carrier power measurement correction |
5.0.0 |
5.1.0 |
18/09/02 |
RAN_17 |
RP-020575 |
121 |
– |
Measurements for observed time difference to GSM cell |
5.0.0 |
5.1.0 |
18/09/02 |
RAN_17 |
RP-020575 |
130 |
– |
Compressed mode limitation |
5.0.0 |
5.1.0 |
18/09/02 |
RAN_17 |
RP-020558 |
128 |
– |
Correction of UE SFN-SFN type 1 measurement |
5.0.0 |
5.1.0 |
21/12/02 |
RAN_18 |
RP-020842 |
131 |
1 |
Received Total Wide Band Power Measurement Definition |
5.1.0 |
5.2.0 |
26/03/03 |
RAN_19 |
RP-030017 |
133 |
3 |
Correction of UTRAN SIR measurement definition |
5.2.0 |
5.3.0 |
26/03/03 |
RAN_19 |
RP-030081 |
134 |
1 |
Non-HSDPA power measurement |
5.2.0 |
5.3.0 |
23/06/03 |
RAN_20 |
RP-030270 |
142 |
– |
Correction of transmitted carrier power definition in case of Tx diversity |
5.3.0 |
5.4.0 |
23/06/03 |
RAN_20 |
RP-030274 |
143 |
– |
Correction of transmitted carrier power of all codes not used for HS-PDSCH or HS-SCCH transmission definition in case of Tx diversity |
5.3.0 |
5.4.0 |
22/09/03 |
RAN_21 |
RP-030452 |
144 |
1 |
Beamforming Enhancement related measurements |
5.4.0 |
5.5.0 |
07/01/04 |
RAN_22 |
– |
– |
– |
Approved to promote to a Release 6 TS and created for M.1457 update |
5.5.0 |
6.0.0 |
07/01/04 |
RAN_22 |
RP-030726 |
145 |
2 |
Beamforming Enhancement related measurements |
5.5.0 |
6.0.0 |
13/12/04 |
RAN_26 |
RP-040449 |
149 |
1 |
Introduction of E-DCH |
6.0.0 |
6.1.0 |
14/03/05 |
RAN_27 |
RP-050050 |
147 |
4 |
Introduction of ‘DL Transmission Branch Load’ measurement |
6.1.0 |
6.2.0 |
14/03/05 |
RAN_27 |
RP-050038 |
153 |
1 |
Removal of TGPL2 |
6.1.0 |
6.2.0 |
14/03/05 |
RAN_27 |
RP-050092 |
154 |
– |
Clarification of the cell on SFN-SFN observed time difference |
6.1.0 |
6.2.0 |
14/03/05 |
RAN_27 |
RP-050088 |
155 |
– |
Introduction of F-DPCH without pilot field |
6.1.0 |
6.2.0 |
16/06/05 |
RAN_28 |
RP-050250 |
161 |
– |
Feature Clean Up: Removal of "CPCH" |
6.2.0 |
6.3.0 |
16/06/05 |
RAN_28 |
RP-050245 |
163 |
– |
Feature Clean Up: Removal of observed time difference to GSM cell measurement |
6.2.0 |
6.3.0 |
16/06/05 |
RAN_28 |
RP-050249 |
165 |
– |
Feature clean up: Removal of the ‘compressed mode by puncturing’ |
6.2.0 |
6.3.0 |
26/09/05 |
RAN_29 |
RP-050453 |
0166 |
1 |
UE power headroom measurement |
6.3.0 |
6.4.0 |
26/09/05 |
RAN_29 |
RP-050440 |
0167 |
– |
Non-HS power measurement |
6.3.0 |
6.4.0 |
20/03/06 |
RAN_31 |
– |
– |
– |
Creation of Release 7 specification (v.7.0.0) at RAN#31 |
6.4.0 |
7.0.0 |
29/09/06 |
RAN_33 |
RP-060495 |
0170 |
3 |
Introduction of a Node B measurement for E-DCH RRM |
7.0.0 |
7.1.0 |
30/05/07 |
RAN_36 |
RP-070391 |
0172 |
5 |
Clarification of UE measurement definitions for RX diversity |
7.1.0 |
7.2.0 |
11/09/07 |
RAN_37 |
RP-070648 |
0176 |
1 |
Adding GANSS related measurements in the FDD physical layer measurements |
7.2.0 |
7.3.0 |
27/11/07 |
RAN_38 |
RP-070946 |
0177 |
– |
Clarification of UE measurement definitions for RX diversity |
7.3.0 |
7.4.0 |
04/03/08 |
RAN_39 |
– |
– |
– |
Release 8 version further to RAN_39 decision |
7.4.0 |
8.0.0 |
28/05/08 |
RAN_40 |
RP-080436 |
188 |
– |
E-UTRA measurements for UTRA – E-UTRA interworking |
8.0.0 |
8.1.0 |
09/09/08 |
RAN_41 |
RP-080672 |
189 |
– |
UPH measurement support for Enhanced Uplink for CELL_FACH state |
8.1.0 |
8.2.0 |
09/09/08 |
RAN_41 |
RP-080666 |
190 |
– |
Modification of RSRQ and removal of RSSI |
8.1.0 |
8.2.0 |
09/09/08 |
RAN_41 |
RP-080666 |
192 |
– |
Modification of RSRP definition |
8.1.0 |
8.2.0 |
03/03/09 |
RAN_43 |
RP-090232 |
194 |
1 |
RSRP and RSRQ Measurement Definitions |
8.2.0 |
8.3.0 |
15/09/09 |
RAN_45 |
RP-090888 |
195 |
1 |
Clarification on reference point of RSRP and RSRQ for EUTRA |
8.3.0 |
8.4.0 |
18/09/09 |
RAN_45 |
– |
– |
– |
Release 9 created further to RAN_45 decision |
8.4.0 |
9.0.0 |
01/12/09 |
RAN_46 |
RP-091170 |
196 |
2 |
Introduction of DC-HSUPA |
9.0.0 |
9.1.0 |
16/03/10 |
RAN_47 |
RP-100205 |
197 |
2 |
Modification of RSRQ definition |
9.1.0 |
9.2.0 |
21/03/11 |
SP_51 |
– |
– |
– |
Release 10 created further to SP_51 decision |
9.2.0 |
10.0.0 |
05/12/11 |
RAN_54 |
RP-111672 |
199 |
– |
Introduction of Uplink Closed Loop Transmit Diversity for HSPA |
10.0.0 |
11.0.0 |
10/09/14 |
RAN_65 |
RP-141480 |
201 |
1 |
Introduction of DCH Enhancements |
11.0.0 |
12.0.0 |
10/09/14 |
RAN_65 |
RP-141484 |
202 |
2 |
Inclusion of definition of WLAN Beacon RSSI in UMTS specifications |
11.0.0 |
12.0.0 |
09/03/15 |
RAN_67 |
RP-150361 |
200 |
2 |
New E-UTRA RSRQ measurement definition |
12.0.0 |
12.1.0 |
07/12/15 |
SP_70 |
Release 13 created further to SP_70 decision |
12.1.0 |
13.0.0 |
Change history |
|||||||
Date |
Meeting |
TDoc |
CR |
Rev |
Cat |
Subject/Comment |
New version |
2016-06 |
RP-72 |
RP-161144 |
0206 |
F |
Clarification on measuring the transmitted code power for the downlink DPCH slot formats #17 and #18 |
13.1.0 |
|
2017-03 |
RP-75 |
– |
– |
– |
– |
Promotion to Release 14 without technical change (MCC) |
14.0.0 |
2018-06 |
RP-80 |
– |
– |
– |
– |
Promotion to Release 15 without technical change (MCC) |
15.0.0 |
2020-07 |
RP-88e |
– |
– |
– |
– |
Upgrade to Rel-16 version without technical change |
16.0.0 |
2022-03 |
RP-95e |
– |
– |
– |
– |
Upgrade to Rel-17 version without technical change |
17.0.0 |