A.9 Output Intermodulation
25.1433GPPRelease 17TSUTRA repeater conformance testing
Figure A.9: Measuring system set-up for Output Intermodulation.
Note that a repeater is a bi-directional device. The signal generator may need protection.
The 5 MHz channel filter is only required if the WCDMA signal generator does not fulfil the unwanted emission requirement for base stations (TS25.141 [11], section 6.5) with at least 10 dB margin in the described set-up.
Annex B (informative):
Derivation of Test Requirements
The Test Requirements in this specification have been calculated by relaxing the Minimum Requirements of the core specification using the Test Tolerances defined in subclause 5.2. When the Test Tolerance is zero, the Test Requirement will be the same as the Minimum Requirement. When the Test Tolerance is non-zero, the Test Requirements will differ from the Minimum Requirements, and the formula used for this relaxation is given in table B.1.
Table B.1: Derivation of Test Requirements
|
Clause number |
Title |
Minimum Requirement in TS 25.106 |
Test Tolerance |
Test Requirement in TS 25.143 |
|
6.1 |
Maximum output power |
In normal conditions Table 6.1 |
0,7 dB, f ≤ 3,0 GHz; 1,0 dB, 3,0 GHz < f ≤ 4,2GHz |
Formula: Upper limit + TT Lower limit – TT In normal conditions refer to Table 6.3 |
|
In extreme conditions Tabel 6.2 |
In extreme conditions refer to Table 6.4 |
|||
|
9.1.2 |
Operating band unwanted emissions |
Tables 9.1, 9.2, 9.3 and 9.4: “Maximum level” = X dB |
1,5 dB, f ≤ 3,0 GHz; (0 dB for the additional Band II, IV, V, X, XII, XIII, XIV, XXV and XXVI require-ments) 1,8 dB, 3,0 GHz < f ≤ 4,2GHz |
Formula: Maximum level + TT Refer to tables 9.5, 9.6, 9.7 and 9.8 Tables 9.8A to 9.8F applies with TT = 0. |
|
7 |
Frequency stability |
7.1 minimum requirement |
12 Hz |
Formula: Relative error + TT Refer to 7.5 Test requirements |
|
8 |
Out of Band Gain |
Table 8.1: Out of band gain limits |
0,5 dB, f ≤ 3,0 GHz; 0,8 dB, 3,0 GHz < f ≤ 4,2GHz |
Formula: Maximum level + TT Refer to table 8.2 |
|
9.2 |
Spurious emissions |
Tables 9.5, to 9.15 |
0 dB |
|
|
10.1 |
Error Vector Magnitude |
10.1.1 Minimum requirement |
0 % |
Formula: RSS Stimulus EVM and Repeater EVM to get target EVM Refer to 10.1.5 Test requirements |
|
10.2 |
Peak code domain error |
10.2.1 Minimum requirement |
1,1 dB |
Formula: Maximum error + TT Refer to 10.2.5 Test requirements |
|
10.3 |
Relative code domain error |
10.3.1 Minimum requirement |
1,7 dB |
Formula: Maximum error + TT Formula for linear offset: Formula TT: Refer to 10.3.5 Test requirements |
|
11 |
Input intermodulation |
11.5 Minimum requirements, and Tables 11.1 and 11.2 |
1,2 dB |
Maximum in-band power increase + TT Refer to 11.5 Test requirements. |
|
12 |
Output intermodulation |
12.1 Minimum requirements |
1,5 dB for operating band unwanted emission (0 dB for the additional Band II, IV, V, X, XII, XIII, XIV, XXV and XXVI require-ments) 0 dB for spurious emissions |
Maximum level + TT Refer to tables 9.5 to 9.19 (Tables 9.8A to 9.8F applies with TT = 0) |
Annex C (informative):
Acceptable uncertainty of Test Equipment
This informative annex specifies the critical parameters of the components of an overall Test System (e.g. signal generators, signal analysers etc.) which are necessary when assembling a Test System which complies with subclause 5.1 Acceptable uncertainty of Test System. These Test Equipment parameters are fundamental to the accuracy of the overall Test System and are unlikely to be improved upon through System Calibration.
Table C.1: Equipment accuracy
|
Test |
Equipment accuracy |
Test condition |
|
6.1 Maximum output power |
Not critical |
|
|
9.1 Spectrum emission mask |
Not critical |
|
|
9.2 Spurious emissions |
Not critical |
|
|
11 Input intermodulation (interferer requirement) |
Not critical |
|
|
7 Frequency error |
±10 Hz + timebase = 12 Hz |
Range 0 to 500 Hz. (This is to allow for UE range that at 0,1 PPM is larger than BTS). |
|
10.1 Error vector magnitude |
±2,5 % (for single code) |
P_Max-3 to P_Max – 18 dB |
|
10.2 Peak code domain error |
||
|
10.3 Relative code domain error |
||
|
8 Out of band gain |
||
|
11 Input intermodulation Characteristics |
||
|
12 Output intermodulation |
Annex D (informative):
Change History
|
TSG |
Doc |
CR |
R |
Title |
Cat |
Curr |
New |
Work Item |
|
RP-31 |
Rel-7 version created from v6.4.0 |
7.0.0 |
||||||
|
RP-31 |
RP-060100 |
0053 |
2 |
Introduction of operating band III to IX requirements in 25.143 |
B |
6.3.0 |
7.0.0 |
TEI7 |
|
RP-31 |
RP-060110 |
0054 |
Correction of spurious emissions for coexistence with GSM900 in same geographic area |
F |
6.3.0 |
7.0.0 |
RinImp-UMTS900 |
|
|
RP-33 |
RP-060520 |
0057 |
1 |
Clean up of Spurious emissions |
A |
7.0.0 |
7.1.0 |
TEI5 |
|
RP-33 |
RP-060521 |
0060 |
1 |
New UTRA Repeater up-link spurious emissions limits for co-existence/co-location with TDD |
A |
7.0.0 |
7.1.0 |
TEI5 |
|
RP-34 |
RP-060811 |
0063 |
1 |
Corrections to input intermodulation |
A |
7.1.0 |
7.2.0 |
TEI5 |
|
RP-36 |
RP-070370 |
0067 |
Category B spurious emission limits for UTRA Repeater |
A |
7.2.0 |
7.3.0 |
TEI4 |
|
|
RP-36 |
RP-070373 |
0068 |
Introduction of operating band X into the repeater specification |
B |
7.2.0 |
7.3.0 |
TEI7 |
|
|
RP-39 |
RP-080126 |
0069 |
Introduction of UMTS1500 requirements |
B |
7.3.0 |
8.0.0 |
RinImp8-UMTS1500 |
|
|
RP-42 |
RP-080943 |
71 |
1 |
Introduction of operating band unwanted emission |
F |
8.0.0 |
8.1.0 |
TEI8 |
|
RP-44 |
RP-080555 |
72 |
Spurious emission testing for repeater capable of UTRA and E-EUTRA |
F |
8.1.0 |
8.2.0 |
TEI8 |
|
|
RP-44 |
RP-080555 |
73 |
Clean up |
F |
8.1.0 |
8.2.0 |
TEI8 |
|
|
RP-44 |
RP-080555 |
74 |
Test procedure amendment |
F |
8.1.0 |
8.2.0 |
TEI8 |
|
|
RP-45 |
RP-080819 |
75 |
Introduction of band XII, XIII, XIV |
F |
8.2.0 |
8.3.0 |
TEI8 |
|
|
RP-45 |
RP-080819 |
76 |
Operating band unwanted emissions test tolerance correction |
F |
8.2.0 |
8.3.0 |
TEI8 |
|
|
RP-45 |
RP-080819 |
77 |
CR to limit the scope to FDD only to 25.143 |
F |
8.2.0 |
8.3.0 |
TEI8 |
|
|
RP-46 |
RP-091277 |
078 |
|
Corrections on additional spectrum emission limits for Bands XII, XIII, XIV |
F |
8.3.0 |
8.4.0 |
TEI8 |
|
RP-46 |
RP-091281 |
079 |
|
Editorial corrections to 25.143 |
F |
8.3.0 |
8.4.0 |
TEI8 |
|
Automatic upgrade from previous Release |
8.4.0 |
9.0.0 |
||||||
|
RP-49 |
RP-100913 |
083 |
2 |
RCDE for 64QAM modulated codes for FDD Repeater |
A |
9.0.0 |
9.1.0 |
TEI7 |
|
RP-49 |
RP-100925 |
080 |
|
Introduction of operating band XIX, XX and XXI and correction of band XI |
F |
9.0.0 |
9.1.0 |
TEI9 |
|
RP-50 |
RP-101336 |
088 |
|
Protection of cdma and E-UTRA bands |
A |
9.1.0 |
9.2.0 |
TEI8 |
|
RP-50 |
RP-101337 |
090 |
|
Removal of brackets |
A |
9.1.0 |
9.2.0 |
TEI8 |
|
RP-50 |
RP-101347 |
084 |
|
Remove test settings for unwanted emissions from the minimum requirement |
F |
9.1.0 |
9.2.0 |
TEI9 |
|
RP-50 |
RP-101347 |
085 |
|
Corrections to the symbols and abbreviations clause related to DTT requirement |
F |
9.1.0 |
9.2.0 |
TEI9 |
|
RP-50 |
RP-101347 |
086 |
|
Co-existence with services in adjacent frequency bands |
F |
9.1.0 |
9.2.0 |
TEI9 |
|
RP-50 |
RP-101347 |
091 |
|
Editorial correction to TS 25.143 |
F |
9.1.0 |
9.2.0 |
TEI9 |
|
RP-51 |
RP-110352 |
092 |
Inclusion of E-UTRA TDD text to co-location on 25.143 |
F |
9.2.0 |
10.0.0 |
TEI10 |
|
|
RP-55 |
RP-120303 |
095 |
1 |
Correction on the table of Regional requirements |
B |
10.0.0 |
10.1.0 |
TEI10 |
|
RP-55 |
RP-120303 |
096 |
1 |
Introduction of operating frequency band XXII |
B |
10.0.0 |
10.1.0 |
TEI10 |
|
RP-55 |
RP-120303 |
097 |
1 |
Introduction of operating frequency band XXV and protection limits towards E-UTRA Band 23 |
B |
10.0.0 |
10.1.0 |
TEI10 |
|
RP-56 |
RP-120783 |
099 |
2 |
Update of the Definition clause with repeaters operating band definition and introduction of minor editorial changes for better alignment with BS core specification |
F |
10.1.0 |
10.2.0 |
TEI10 |
|
RP-56 |
RP-120765 |
104 |
|
Additional spurious emissions requirements for PHS |
A |
10.1.0 |
10.2.0 |
TEI8 |
|
RP-57 |
RP-121313 |
105 |
2 |
Introduction of missing Spurious Emission and Input Intermodulation protection limits towards E-UTRA FDD Band 24 |
F |
10.2.0 |
10.3.0 |
TEI10 |
|
RP-57 |
RP-121312 |
109 |
1 |
Repeater test uncertainties for UTRA bands above 3 GHz |
F |
10.2.0 |
10.3.0 |
RInImp8-UMTSLTE3500 |
|
SP-57 |
– |
– |
– |
Update to Rel-11 version (MCC) |
– |
10.3.0 |
11.0.0 |
– |
|
RP-58 |
RP-121867 |
0113 |
Introduction of Spurious Emission limits and Input Intermodulation requirements towards missing UTRA and E-UTRA TDD frequency bands |
A |
11.0.0 |
11.1.0 |
TEI10 |
|
|
RP-58 |
RP-121867 |
0114 |
Introduction of a Note on non deployment of operating bands with overlapping frequency ranges for the tables for Input Intermodulation requirements |
A |
11.0.0 |
11.1.0 |
TEI10 |
|
|
RP-58 |
RP-121858 |
0115 |
Modifications of frequency ranges for E-UTRA Band 6, 18, 19 in the Tables for Spurious Emission limits and Input Intermodulation requirements |
A |
11.0.0 |
11.1.0 |
RInImp9-UMTSLTE800 |
|
|
RP-58 |
RP-121867 |
0118 |
The special cases for protection of UTRA Band III and Band X in co-existence and co-location with UTRA Repeaters |
A |
11.0.0 |
11.1.0 |
TEI10 |
|
|
SP-65 |
– |
– |
– |
Update to Rel-12 version (MCC) |
– |
11.1.0 |
12.0.0 |
|
|
RP-66 |
RP-142154 |
121 |
|
Update with regard to operating bands of TS25.143 |
F |
12.0.0 |
12.1.0 |
LTE_UTRA_SDL_BandL-Perf, LTE450_Brazil-Perf, LTE_WCS_band-Perf, LTE_DL_FDD700-Perf, LTE_APAC700-Perf, LTE_e850_LB-Perf,E850_UB-Perf |
|
SP-70 |
– |
– |
– |
Update to Rel-13 version (MCC) |
– |
12.1.0 |
13.0.0 |
|
|
RP-75 |
– |
– |
– |
Update to Rel-14 version (MCC) |
– |
13.0.0 |
14.0.0 |
|
Change history |
|||||||
|
Date |
Meeting |
TDoc |
CR |
Rev |
Cat |
Subject/Comment |
New version |
|
2018-06 |
SA#80 |
– |
– |
– |
– |
Update to Rel-15 version (MCC) |
15.0.0 |
|
2020-06 |
SA#88 |
– |
– |
– |
– |
Update to Rel-16 version (MCC) |
16.0.0 |
|
2022-03 |
SA#95 |
Update to Rel-17 version (MCC) |
17.0.0 |
||||