9 Unwanted emission
25.1063GPPRelease 17TSUTRA repeater radio transmission and reception
Unwanted emissions consist of out-of-band emissions and spurious emissions [1]. Out of band emissions are unwanted emissions immediately outside the pass band bandwidth resulting from the modulation process and non-linearity in the transmitter, but excluding spurious emissions. Spurious emissions are emissions which are caused by unwanted transmitter effects such as harmonics emission, parasitic emission, intermodulation products and frequency conversion products, but exclude out of band emissions.
The out-of-band emissions requirement for repeater is specified both in terms operating band unwanted emissions and protection of the BS receiver in the operating band. The Operating band unwanted emissions define all unwanted emissions in the repeater operating band plus the frequency ranges 10 MHz above and 10 MHz below that band. Unwanted emissions outside of this frequency range are limited by a spurious emissions requirement.
9.1 Out of band emission
9.1.1 Void
9.1.2 Operating band unwanted emissions
Operating band unwanted emissions comprise an emission mask applied outside the repeater passband and a general requirement applied outside the mask but inside the frequency range of the operating band unwanted emissions.
The general operating band unwanted emissions limits are given in table 9.0.
Table 9.0: General operating band unwanted emissions requirements
Frequency range of operating band |
Category A |
Category B |
Measurement bandwidth |
Notes |
1 GHz |
-13 dBm |
-16 dBm |
100 kHz |
1,2 |
1 GHz |
-13 dBm |
-15 dBm |
1 MHz |
2,3 |
NOTE 1: Bandwidth as in ITU-R Recommendation SM.329 [1], s4.1.
NOTE 2: Limit based on ITU-R Recommendation SM.329 [1], s4.3 and Annex 7.
NOTE 3: Bandwidth as in ITU-R Recommendation SM.329 [1], s4.1. Upper frequency as in ITU-R SM.329 [1], s2.5 table 1.
The mask defined in tables 9.1 to 9.4 below may be mandatory in certain regions. In other regions this mask may not be applied.
For regions where this clause applies, the requirement shall be met by a repeater’s RF-signal output at maximum gain with WCDMA signals in the pass band of the repeater, at levels that produce the maximum rated output power per channel. The requirements shall also apply at maximum gain without WCDMA signals in the pass band.
Emissions shall not exceed the maximum level specified in tables 9.1 to 9.4 for the appropriate repeater maximum output power, in the frequency range from f = 2,5 MHz to fmax from the 5 MHz channel, where:
– f is the separation between the centre frequency of first or last 5 MHz channel used in the pass band and the nominal -3 dB point of the measuring filter closest to the carrier frequency.
– f_offset is the separation between the centre frequency of first or last 5 MHz channel in the pass band and the centre of the measuring filter.
– f_offsetmax is 12,5 MHz.
– f max is equal to f_offsetmax minus half of the bandwidth of the measurement filter.
Figure 9.1: Illustrative diagram of emission mask
Table 9.1: Emission mask values, maximum output power P 43 dBm
Frequency offset of measurement filter -3dB point, f |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement |
Measurement bandwidth (Note 2) |
2,5 MHz f < 2,7 MHz |
2,515MHz f_offset < 2,715MHz |
-14 dBm |
30 kHz |
2,7 MHz f < 3,5 MHz |
2,715MHz f_offset < 3,515MHz |
30 kHz |
|
(Note 1) |
3,515MHz f_offset < 4,0MHz |
-26 dBm |
30 kHz |
3,5 MHz f f max |
4,0MHz f_offset < f_offsetmax |
-13 dBm |
1 MHz |
Table 9.2: Emission mask values, maximum output power 39 P < 43 dBm
Frequency offset of measurement filter -3dB point, f |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement |
Measurement bandwidth (Note 2) |
2,5 MHz f < 2,7 MHz |
2,515MHz f_offset < 2,715MHz |
-14 dBm |
30 kHz |
2,7 MHz f < 3,5 MHz |
2,715MHz f_offset < 3,515MHz |
30 kHz |
|
(Note 1) |
3,515MHz f_offset < 4,0MHz |
-26 dBm |
30 kHz |
3,5 MHz f < 7,5 MHz |
4,0MHz f_offset < 8,0MHz |
-13 dBm |
1 MHz |
7,5 MHz f f max |
8,0MHz f_offset < f_offsetmax |
P – 56 dB |
1 MHz |
Table 9.3: Emission mask values, maximum output power 31 P < 39 dBm
Frequency offset of measurement filter -3dB point, f |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement |
Measurement bandwidth (Note 2) |
2,5 MHz f < 2,7 MHz |
2,515MHz f_offset < 2,715MHz |
P – 53 dB |
30 kHz |
2,7 MHz f < 3,5 MHz |
2,715MHz f_offset < 3,515MHz |
30 kHz |
|
(Note 1) |
3,515MHz f_offset < 4,0MHz |
P-65 dB |
30 kHz |
3,5 MHz f < 7,5 MHz |
4,0MHz f_offset < 8,0MHz |
P – 52 dB |
1 MHz |
7,5 MHz f f max |
8,0MHz f_offset < f_offsetAmax |
P – 56 dB |
1 MHz |
Table 9.4: Emission mask values, maximum output power P < 31 dBm
Frequency offset of measurement filter -3dB point, f |
Frequency offset of measurement filter centre frequency, f_offset |
Minimum requirement |
Measurement bandwidth (Note 2) |
2,5 MHz f < 2,7 MHz |
2,515MHz f_offset < 2,715MHz |
-22 dBm |
30 kHz |
2,7 MHz f < 3,5 MHz |
2,715MHz f_offset < 3,515MHz |
30 kHz |
|
( Note 1) |
3,515MHz f_offset < 4,0MHz |
-34 dBm |
30 kHz |
3,5 MHz f < 7,5 MHz |
4,0MHz f_offset < 8,0MHz |
-21 dBm |
1 MHz |
7,5 MHz f f max |
8,0MHz f_offset < f_offsetmax |
-25 dBm |
1 MHz |
For operation in band II, IV, V, X, XII, XIII, XIV, XXV and XXVI, the applicable additional requirement in Tables 9.4A, 9.4B or 9.4C apply in addition to the minimum requirements in Tables 9.1 to 9.4.
Table 9.4A: Additional emission mask values for Bands II, IV, X, XXV
Frequency offset of measurement filter ‑3dB point, f |
Frequency offset of measurement filter centre frequency, f_offset |
Additional requirement |
Measurement bandwidth |
2.5 MHz f < 3.5 MHz |
2.515MHz f_offset < 3.515MHz |
-15 dBm |
30 kHz |
3.5 MHz f fmax |
4.0MHz f_offset < f_offsetmax |
-13 dBm |
1 MHz |
Table 9.4B: Additional emission mask values for Band V and XXVI
Frequency offset of measurement filter ‑3dB point, f |
Frequency offset of measurement filter centre frequency, f_offset |
Additional requirement |
Measurement bandwidth |
2.5 MHz f < 3.5 MHz |
2.515MHz f_offset < 3.515MHz |
-15 dBm |
30 kHz |
3.5 MHz f fmax |
3.55MHz f_offset < f_offsetmax |
-13 dBm |
100 kHz |
Table 9.4C: Additional emission mask values for Bands XII, XIII, XIV
Frequency offset of measurement filter ‑3dB point, f |
Frequency offset of measurement filter centre frequency, f_offset |
Additional requirement |
Measurement bandwidth |
2.5 MHz f < 2.6 MHz |
2.515MHz f_offset < 2.615MHz |
-13 dBm |
30 kHz |
2.6 MHz f fmax |
2.65MHz f_offset < f_offsetmax |
-13 dBm |
100 kHz |
In certain regions the following requirement may apply for protection of DTT. For UTRA Repeater operating in Band XX, the level of emissions in the band 470-790 MHz, measured in an 8MHz filter bandwidth on centre frequencies Ffilter according to Table 9.4.D, shall not exceed the maximum emission level PEM,N declared by the manufacturer.
Table 9.4.D: Declared emissions levels for protection of DTT
Filter centre frequency, Ffilter |
Measurement bandwidth |
Declared emission level [dBm] |
Ffilter = 8*N + 306 (MHz); |
8 MHz |
PEM,N |
NOTE: The regional requirement is defined in terms of EIRP (effective isotropic radiated power), which is dependent on both the repeater emissions at the antenna connector and the deployment (including antenna gain and feeder loss). The requirement defined above provides the characteristics of the repeater needed to verify compliance with the regional requirement. Compliance with the regional requirement can be determined using the method outlined in TS 25.104 [6] Annex D.
Note for Tables 9.1, 9.2, 9.3, 9.4, 9.4A, 9.4B and 9.4C:
NOTE 1: This frequency range ensures that the range of values of f_offset is continuous.
In certain regions, the following requirements may apply to UTRA repeaters operating in Band XXXII within 1452-1492 MHz. The level of unwanted emissions, measured on centre frequencies f_offset with filter bandwidth, according to Table 9.4E shall neither exceed the maximum emission level PEM,B32,a , PEM,B32,b nor PEM,B32,c declared by the manufacturer.
Table 9.4E: Declared operating band XXXII unwanted emission within 1452-1492 MHz
Frequency offset of measurement filter centre frequency, f_offset |
Declared emission level [dBm] |
Measurement bandwidth |
5 MHz |
PEM,B32,a |
5 MHz |
10 MHz |
PEM,B32,b |
5 MHz |
15 MHz ≤ f_offset ≤ f_offsetmax, B32 |
PEM,B32,c |
5 MHz |
NOTE: f_offsetmax, B32 denotes the frequency difference between the lower channel carrier frequency and 1454.5 MHz, and the frequency difference between the upper channel carrier frequency and 1489.5 MHz for the set channel position. |
NOTE: The regional requirement, included in [7], is defined in terms of EIRP per antenna, which is dependent on both the repeater emissions at the antenna connector and the deployment (including antenna gain and feeder loss). The requirement defined above provides the characteristics of the base station needed to verify compliance with the regional requirement. The assessment of the EIRP level is described in Annex H of TS36.104 [8].
In certain regions, the following requirement may apply to UTRA repeaters operating in Band XXXII within 1452-1492 MHz for the protection of services in spectrum adjacent to the frequency range 1452-1492 MHz. The level of emissions, measured on centre frequencies Ffilter with filter bandwidth according to Table 9.4F shall neither exceed the maximum emission level PEM,B32,d nor PEM,B32,e declared by the manufacturer. This requirement applies in the frequency range 1429-1518 MHz even though part of the range falls in the spurious domain.
Table 9.4F: Operating band XXXII declared emission outside 1452-1492 MHz
Filter centre frequency, Ffilter |
Declared emission level [dBm] |
Measurement bandwidth |
---|---|---|
1429.5 MHz ≤ Ffilter ≤ 1448.5 MHz |
PEM,B32,d |
1 MHz |
Ffilter = 1450.5 MHz |
PEM,B32,e |
3 MHz |
Ffilter = 1493.5 MHz |
PEM,B32,e |
3 MHz |
1495.5 MHz ≤ Ffilter ≤ 1517.5 MHz |
PEM,B32,d |
1 MHz |
NOTE: The regional requirement, included in [7], is defined in terms of EIRP, which is dependent on both the repeater emissions at the antenna connector and the deployment (including antenna gain and feeder loss). The requirement defined above provides the characteristics of the base station needed to verify compliance with the regional requirement. The assessment of the EIRP level is described in Annex H of TS36.104 [8].
9.1.3. Protection of the BS receiver in the operating band
This requirement shall be applied for the protection of UTRA FDD BS receiver in geographic areas in which UTRA-FDD Repeater and UTRA-FDD BS are deployed.
The requirement applies outside the emission mask.
9.1.3.1 Minimum Requirement
This requirement applies to the uplink of the repeater, at maximum gain.
The power of any operating band unwanted emission shall not exceed the limits in Table 9.7A.
Table 9.7A: Uplink operating band unwanted emissions limits for protection of the BS receiver
Maximum Level |
Measurement Bandwidth |
Note |
-53 dBm |
100 kHz |
NOTE 1: These requirements in Table 9.7A: for the uplink direction of the Repeater reflect what can be achieved with present state of the art technology and are based on a coupling loss of 73 dB between a Repeater and a UTRA FDD BS receiver.
NOTE 2: The requirements shall be reconsidered when the state of the art technology progresses.
NOTE 3: The protection of R-GSM is for further study.
9.1.4 Co-existence with services in adjacent frequency bands
This requirement may be applied for the protection in bands adjacent to bands I, or VII, as defined in clause 5.1 in geographic areas in which both an adjacent band service and UTRA are deployed.
The requirement applies only to the down-link direction of the repeater.
9.1.4.1 Minimum requirement
The power of any spurious emission shall not exceed:
Table 9.16: UTRA Repeater down-link spurious emissions limits for protection of adjacent band services
Operating Band |
Band |
Maximum Level |
Measurement Bandwidth |
Note |
I |
2100-2105 MHz |
-30 + 3.4 (f – 2100 MHz) dBm |
1 MHz |
|
2175-2180 MHz |
-30 + 3.4 (2180 MHz – f) dBm |
1 MHz |
||
VII |
2610-2615 MHz |
-30 + 3.4 (f ‑ 2610 MHz) dBm |
1 MHz |
|
2695-2700 MHz |
-30 + 3.4 (2700 MHz ‑ f) dBm |
1 MHz |
9.2 Spurious emissions
Spurious emissions are emissions which are caused by unwanted transmitter effects such as harmonics emission, parasitic emission, intermodulation products and frequency conversion products, but exclude out of band emissions. This is measured at the repeaters RF output port.
The spurious emission limits apply from 9 kHz to 12.75 GHz (or above, as indicated in Table 9.5 and 9.5A), excluding the frequency range from 10 MHz below the lowest frequency of the repeaters operating band up to 10 MHz above the highest frequency of the repeaters operating band. Exceptions are the requirement in Table 9.13 and 9.16 that apply also closer than 10 MHz from repeaters operating band.
Unless otherwise stated, all requirements are measured as mean power.
9.2.1 General Requirements
The requirements of either subclause 9.2.1.1 or subclause 9.2.1.2 shall apply whatever the type of repeater considered (one or several pass bands). It applies for all configurations foreseen by the manufacturer’s specification.
9.2.1.1 Minimum Requirement (Category A)
The following requirements shall be met in cases where Category A limits for spurious emissions, as defined in ITU-R Recommendation SM.329 [1], are applied.
At maximum repeater gain, with WCDMA signals in the pass band of the repeater, at levels that produce the maximum rated output power per channel, the power of any spurious emission shall not exceed the limits specified in table 9.5. The requirements shall also apply at maximum gain without WCDMA signals in the pass band.
When the power in all channels is increased by 10 dB, compared to the input level producing the maximum rated output power, the requirement shall still be met.
Table 9.5: Up-link and down-link: General spurious emissions limits, Category A
Band |
Maximum level |
Measurement Bandwidth |
Note |
9kHz – 150kHz |
-13 dBm |
1 kHz |
Note 1 |
150kHz – 30MHz |
10 kHz |
Note 1 |
|
30MHz – 1GHz |
100 kHz |
Note 1 |
|
1GHz – 12,75 GHz |
1 MHz |
Note 2 |
|
12,75GHz – 5th harmonic of the upper frequency edge of the DL or UL operating band for DL or UL spurious emissions, respectively |
1 MHz |
Note 2, Note 3 |
|
NOTE 1: Bandwidth as in ITU-R SM.329 [1], s4.1 NOTE 2: Upper frequency as in ITU-R SM.329 [1], s2.5 table 1 NOTE 3: Applies only for Band XXII |
9.2.1.2 Minimum Requirement (Category B)
The following requirements shall be met in cases where Category B limits for spurious emissions, as defined in ITU-R Recommendation SM.329 [1], are applied.
At maximum repeater gain, with WCDMA signals in the pass band of the repeater, at levels that produce the maximum rated power output per channel, the power of any spurious emission shall not exceed the limits specified in table 9.5A for the down- and up-link.
The requirements shall also apply at maximum gain without WCDMA signals in the pass band.
When the power in all channels is increased by 10 dB, compared to the input level producing the maximum rated output power, the requirement shall still be met.
Table 9.5A: General spurious emissions limits (Category B)
Band |
Maximum Level |
Measurement Bandwidth |
Note |
9 kHz 150 kHz |
-36 dBm |
1 kHz |
Note 1 |
150 kHz 30 MHz |
-36 dBm |
10 kHz |
Note 1 |
30 MHz 1 GHz |
-36 dBm |
100 kHz |
Note 1 |
1 GHz 12.75 GHz |
-30 dBm |
1 MHz |
Note 2 |
12.75 GHz 5th harmonic of the upper frequency edge of the DL or UL operating band for DL or UL spurious emissions, respectively |
-30 dBm |
1 MHz |
Note 2, Note 3 |
NOTE 1: Bandwidth as in ITU-R Recommendation SM.329 [1], s4.1 NOTE 2: Bandwidth as in ITU-R Recommendation SM.329 [1], s4.1. Upper frequency as in ITU-R SM.329 [1], s2.5 table 1 NOTE 3: Applies only for Band XXII |
Table 9.6: (Void)
Table 9.6A: (Void)
Table 9.6B: (Void)
Table 9.6C: (Void)
Table 9.6D: (Void)
Table 9.6E: (Void)
Table 9.6F: (Void)
9.2.2 Void
9.2.3 Co-existence with other systems in the same geographical area
These requirements may be applied for the protection of UE, MS and/or BS operating in other frequency bands in the same geographical area. The requirements may apply in geographic areas in which both UTRA FDD Repeater and a system operating in another frequency band than the FDD operating band are deployed. The system operating in the other frequency band may be GSM900, DCS1800, PCS1900, GSM850, E-UTRA FDD and/or UTRA FDD.
9.2.3.1 Minimum Requirements
The power of any spurious emission shall not exceed the limits of Table 9.9 for a UTRA FDD Repeater where requirements for co-existence with the system listed in the first column apply.
Table 9.9: UTRA Repeater up-link and down-link spurious emissions limits in geographic coverage area of systems operating in other frequency bands
System type operating in the same geographical area |
Band for co-existence requirement |
Maximum Level |
Measurement Bandwidth |
Note |
GSM900 |
921 ‑ 960 MHz |
-57 dBm |
100 kHz |
This requirement does not apply to UTRA FDD Repeater operating in band VIII |
876 – 915 MHz |
-61 dBm |
100 kHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band VIII, since it is already covered by the requirement in sub-clause 9.1.3 |
|
DCS1800 |
1805 ‑ 1880 MHz |
-47 dBm |
100 kHz |
This requirement does not apply to UTRA FDD Repeater operating in band III. |
1710 – 1785 MHz |
-61 dBm |
100 kHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band III, since it is already covered by the requirement in sub-clause 9.1.3. |
|
PCS1900 |
1930 ‑ 1990 MHz |
-47 dBm |
100 kHz |
This requirement does not apply to UTRA FDD Repeater operating in frequency band II or band XXV. |
1850 ‑ 1910 MHz |
-61 dBm |
100 kHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in frequency band II or band XXV, since it is already covered by the requirement in sub-clause 9.1.3. |
|
GSM850 or CDMA850 |
869 – 894 MHz |
-57 dBm |
100 kHz |
This requirement does not apply to UTRA FDD Repeater operating in frequency band V or XXVI. |
824 ‑ 849 MHz |
-61 dBm |
100 kHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in frequency band V or XXVI, since it is already covered by the requirement in sub-clause 9.1.3. |
|
UTRA FDD Band I or E‑UTRA Band 1 |
2110 – 2170 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band I. |
1920 – 1980 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band I, since it is already covered by the requirement in sub-clause 9.1.3. |
|
UTRA FDD Band II or E‑UTRA Band 2 |
1930 – 1990 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band II or band XXV. |
1850 – 1910 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band II or band XXV, since it is already covered by the requirement in sub-clause 9.1.3. |
|
UTRA FDD Band III or E‑UTRA Band 3 |
1805 – 1880 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band III or band IX. |
1710 – 1785 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band III, since it is already covered by the requirement in sub-clause 9.1.3. This requirement does not apply to the uplink of UTRA FDD Repeater operating in band IX in the frequency Range from 1749,9 MHz to 1784,9 MHz, since it is already covered by the requirement in clause 9.1.3. |
|
UTRA FDD Band IV or E‑UTRA Band 4 |
2110 – 2155 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band IV or band X. |
1710 – 1755 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band IV or band X, since it is already covered by the requirement in sub-clause 9.1.3. |
|
UTRA FDD Band V or E‑UTRA Band 5 |
869 – 894 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band V or XXVI. |
824 – 849 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band V or XXVI, since it is already covered by the requirement in sub-clause 9.1.3. |
|
UTRA FDD Band VI or XIX or E‑UTRA Band 6, 18 or 19 |
860 – 890 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band V, VI, XIX, XX or XXVI. |
815 – 830 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band V, VI, XIX, XX or XXVI. |
|
830 – 845 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band VI or XIX, since it is already covered by the requirement in sub-clause 9.1.3. This requirement does not apply to the UL of the UTRA FDD Repeater operating in band V, XX or XXVI. |
|
UTRA FDD Band VII or E‑UTRA Band 7 |
2620 – 2690 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band VII. |
2500 – 2570 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band VII, since it is already covered by the requirement in sub-clause 9.1.3. |
|
UTRA FDD Band VIII or E‑UTRA Band 8 |
925 – 960 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band VIII. |
880 – 915 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band VIII, since it is already covered by the requirement in sub-clause 9.1.3. |
|
UTRA FDD Band IX or E‑UTRA Band 9 |
1844.9 – 1879.9 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band III or band IX. |
1749. 9 – 1784.9 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band III or band IX, since it is already covered by the requirement in sub-clause 9.1.3. |
|
UTRA FDD Band X or E‑UTRA Band 10 |
2110 – 2170 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band IV or band X. |
1710 – 1770 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band X, since it is already covered by the requirement in sub-clause 9.1.3. This requirement does not apply to the uplink of UTRA FDD Repeater operating in band IV in the frequency Range from 1710 MHz to 1755 MHz, since it is already covered by the requirement in clause 9.1.3. |
|
UTRA FDD Band XI or XXI or E‑UTRA Band 11 or 21 |
1475.9 – 1510.9 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band XI, band XXI or XXXII. |
1427.9 – 1447.9 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band XI, since it is already covered by the requirement in sub-clause 9.1.3. For UTRA repeaters operating in band XXXII, this requirement applies for carriers allocated within 1475.9MHz and 1495.9MHz. |
|
1447.9 – 1462.9 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band XXI, since it is already covered by the requirement in sub-clause 9.1.3. For UTRA repeaters operating in band XXXII, this requirement applies for carriers allocated within 1475.9MHz and 1495.9MHz. |
|
UTRA FDD Band XII or E‑UTRA Band 12 |
728 – 746 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band XII. |
698 – 716 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band XII, since it is already covered by the requirement in sub-clause 9.1.3. |
|
UTRA FDD Band XIII or E‑UTRA Band 13 |
746 – 756 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band XIII. |
777 – 787 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band XIII, since it is already covered by the requirement in sub-clause 9.1.3. |
|
UTRA FDD Band XIV or E‑UTRA Band 14 |
758 – 768 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band XIV. |
788 – 798 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band XIV, since it is already covered by the requirement in sub-clause 9.1.3. |
|
E‑UTRA Band 17 |
734 – 746 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band XII. |
704 – 716 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band XII, since it is already covered by the requirement in sub-clause 9.1.3. |
|
UTRA FDD Band XX or E‑UTRA Band 20 |
791 – 821 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band XX. |
832 – 862 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD Repeater operating in band XIII, since it is already covered by the band XX requirement in sub-clause 9.1.3. |
|
UTRA FDD Band XXII or E-UTRA Band 22 |
3510 – 3590 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD repeater operating in band XXII. |
3410 – 3490 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the uplink of the UTRA FDD repeater operating in band XXII, since it is already covered by the requirement in sub-clause 9.1.3. |
|
E-UTRA Band 23 |
2180 – 2200 MHz |
-52 dBm |
1 MHz |
|
2000 – 2020 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band II or band XXV, where the limits are defined separately. |
|
2000 – 2010 MHz |
-30 dBm |
1 MHz |
This requirement only applies to UTRA FDD Repeater operating in band II or band XXV. This requirement applies starting 5 MHz above the band XXV DL operating band. |
|
2010 – 2020 MHz |
-49 dBm |
1 MHz |
||
E-UTRA Band 24 |
1525 – 1559 MHz |
-52 dBm |
1 MHz |
|
1626.5 – 1660.5 MHz |
-49 dBm |
1 MHz |
||
UTRA FDD Band XXV or E-UTRA Band 25 |
1930 – 1995 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD repeater operating in band II or band XXV. |
1850 – 1915 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD repeater operating in band XXV since it is already covered by the requirement in sub-clause 9.1.3. For UTRA FDD repeater operating in band II, it applies for 1910 MHz to 1915 MHz, while the rest is covered in sub-clause 9.1.3. |
|
UTRA FDD Band XXVI or E-UTRA Band 26 |
859 – 894 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD repeater operating in band V or band XXVI. |
814 – 849 MHz |
-49 dBm |
1 MHz |
This requirement does not apply to the UL of the UTRA FDD repeater operating in band XXVI since it is already covered by the requirement in sub-clause 9.1.3. For UTRA FDD repeater operating in band V, it applies for 814 MHz to 824 MHz, while the rest is covered in sub-clause 9.1.3. |
|
E-UTRA Band 27 |
852 – 869 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD repeater operating in band V or band XXVI. |
807 – 824 MHz |
-49 dBm |
1 MHz |
For UTRA FDD repeater operating in band XXVI, it applies for 807 MHz to 814 MHz, while the rest is covered in sub-clause 9.1.3. |
|
E-UTRA Band 28 |
758 – 803 MHz |
-52 dBm |
1 MHz |
|
703 – 748 MHz |
-49 dBm |
1 MHz |
||
E-UTRA Band 29 |
717 – 728 MHz |
-52 dBm |
1 MHz |
|
E-UTRA Band 30 |
2350 – 2360 MHz |
-52 dBm |
1 MHz |
|
2305 – 2315 MHz |
-49 dBm |
1 MHz |
||
E-UTRA Band 31 |
462.5 – 467.5 MHz |
-52 dBm |
1 MHz |
|
452.5 – 457.5 MHz |
-49 dBm |
1 MHz |
||
UTRA FDD Band XXXII or E-UTRA Band 32 |
1452 – 1496 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA repeater operating in Band XI, XXI, or XXXII |
NOTE 1: The co-existence requirements do not apply for the 10 MHz frequency range immediately outside the repeaters operating band (see Table 5.1). Emission limits for this excluded frequency range may be covered by local or regional requirements. NOTE 2: The table above assumes that two operating bands, where the frequency ranges would be overlapping, are not deployed in the same geographical area. For such a case of operation with overlapping frequency arrangements in the same geographical area, special co-existence requirements may apply that are not covered by the 3GPP specifications. |
9.2.4 Co-existence with co-located and co-sited Base Stations
These requirements may be applied for the protection of other BS receivers when GSM900 and/or DCS1800, PCS1900, GSM850, E-UTRA FDD and/or UTRA FDD BS are co-located with a UTRA FDD Repeater.
9.2.4.1 Minimum Requirements
The power of any spurious emission shall not exceed the limits of Table 9.10 for a UTRA FDD Repeater where requirements for co-location with the Base Station listed in the first column apply.
Table 9.10: UTRA Repeater up-link and down-link spurious emissions limits for Repeater co-located with Base Stations
Type of co-located Base Station |
Band for co-location requirement |
Maximum Level |
Measurement Bandwidth |
Note |
||||
GSM900 |
876 – 915 MHz |
-98 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band VIII. The sub-clause 9.1.3 requirement applies, but requires a 75dB coupling loss between BS and the repeater UL transmit port. |
||||
DCS1800 |
1710 – 1785 MHz |
-98 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band III. The sub-clause 9.1.3 requirement applies, but requires a 75dB coupling loss between BS and the repeater UL transmit port. |
||||
PCS1900 |
1850 – 1910 MHz |
-98 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band II or band XXV. The sub-clause 9.1.3 requirement applies, but requires a 75dB coupling loss between BS and the repeater UL transmit port. |
||||
GSM850 or CDMA850 |
824 – 849 MHz |
-98 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band V or band XXVI. The sub-clause 9.1.3 requirement applies, but requires a 75dB coupling loss between BS and the repeater UL transmit port. |
||||
UTRA FDD Band I or E‑UTRA Band 1 |
1920 – 1980 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band I. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
UTRA FDD Band II or E‑UTRA Band 2 |
1850 – 1910 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band II or band XXV. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
UTRA FDD Band III or E‑UTRA Band 3 |
1710 – 1785 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band III. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. This requirement does not apply to the uplink of UTRA FDD Repeater operating in band IX in the frequency Range from 1749,9 MHz to 1784,9 MHz, since it is already covered by the requirement in clause 9.1.3, but requires a 73dB coupling loss between base station and the repeater UL transmit port. |
||||
UTRA FDD Band IV or E‑UTRA Band 4 |
1710 – 1755 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band IV or band X. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
UTRA FDD Band V or E‑UTRA Band 5 |
824 – 849 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band V or band XXVI. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
UTRA FDD Band VI or XIX or E‑UTRA Band 6, 18 or 19 |
815 – 830 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band V, VI, XIX, XX or XXVI. |
||||
830 – 845 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band VI or XIX. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. This requirement does not apply to the UL of UTRA FDD Repeater operating in band V, XX or XXVI. |
|||||
UTRA FDD Band VII or E‑UTRA Band 7 |
2500 – 2570 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band VII. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
UTRA FDD Band VIII or E‑UTRA Band 8 |
880 – 915 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band VIII. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
UTRA FDD Band IX or E‑UTRA Band 9 |
1749.9 – 1784.9 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band III or band IX. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
UTRA FDD Band X or E‑UTRA Band 10 |
1710 – 1770 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band X. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. This requirement does not apply to the uplink of E-UTRA FDD Repeater operating in band IV in the frequency range from 1710 MHz to 1755 MHz, since it is already covered by the requirement in clause 9.1.3, but requires a 73dB coupling loss between base station and the repeater UL transmit port. |
||||
UTRA FDD Band XI or XXI or E‑UTRA Band 11 or 21 |
1427.9 – 1447.9 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band XI. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. This requirement applies only for operation between 1475.9 MHz and 1495.9 MHz for UTRA FDD repeater operating in band XXXII. |
||||
1447.9 – 1462.9 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band XXI. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. This requirement applies only for operation between 1475.9 MHz and 1495.9 MHz for UTRA FDD repeater operating in band XXXII. |
|||||
UTRA FDD Band XII or E‑UTRA Band 12 |
698 – 716 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band XII. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
UTRA FDD Band XIII or E‑UTRA Band 13 |
777 – 787 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band XIII. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
UTRA FDD Band XIV or E‑UTRA Band 14 |
788 – 798 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band XIV. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
E‑UTRA Band 17 |
704 – 716 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band XII. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
UTRA FDD Band XX or E‑UTRA Band 20 |
832 – 862 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band XX. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
UTRA FDD Band XXII or E‑UTRA Band 22 |
3410 – 3490 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band XXII. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
E‑UTRA Band 23 |
2000 – 2020 MHz |
-96 dBm |
100 kHz |
|||||
E‑UTRA Band 24 |
1626.5 – 1660.5 MHz |
-96 dBm |
100 kHz |
|||||
UTRA FDD Band XXV or E‑UTRA Band 25 |
1850 – 1915 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band XXV. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. For UTRA FDD Repeater operating in band 2, it applies from 1910MHz to 1915MHz, while the rest is covered in sub-clause 9.1.3, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
UTRA FDD Band XXVI or E UTRA Band 26 |
814 – 849 MHz |
-96 dBm |
100 kHz |
This requirement does not apply to the UL of UTRA FDD Repeater operating in band XXVI. The sub-clause 9.1.3 requirement applies, but requires a 73dB coupling loss between BS and the repeater UL transmit port. For UTRA FDD Repeater operating in band V, it applies from 814 MHz to 824MHz, while the rest is covered in sub-clause 9.1.3, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
E-UTRA Band 27 |
807 – 824 MHz |
-96 dBm |
100 kHz |
For UTRA FDD Repeater operating in band XXVI, this requirement applies from 807 MHz to 814MHz, while the rest is covered in sub-clause 9.1.3, but requires a 73dB coupling loss between BS and the repeater UL transmit port. |
||||
E-UTRA Band 28 |
703 – 748 MHz |
-96 dBm |
100 kHz |
|||||
E-UTRA Band 30 |
2305 – 2315 MHz |
-96 dBm |
100 kHz |
|||||
E.UTRA Band 31 |
452.5 – 457.5 MHz |
-96 dBm |
100 kHz |
|||||
NOTE 1: The co-location requirements do not apply for the 10 MHz frequency range immediately outside the repeater operating band (see Table 5.1). The current state-of-the-art technology does not allow a single generic solution for co-location with other system on adjacent frequencies for 30 dB UTRA Repeater-BS minimum coupling loss. However, there are certain site-engineering solutions that can be used. These techniques are addressed in TR 25.942 [5]. NOTE 2: The table above assumes that two operating bands, where the frequency ranges would be overlapping, are not deployed in the same geographical area. For such a case of operation with overlapping frequency arrangements in the same geographical area, special co-existence requirements may apply that are not covered by the 3GPP specifications. |
9.2.5 Co-existence with PHS
This requirement may be applied for the protection of PHS in geographic areas in which both PHS and UTRA-FDD Repeaters are deployed. This requirement is also applicable at specified frequencies falling between 12,5 MHz below the centre frequency of the first 5 MHz channel or more than 12,5 MHz above the centre frequency of the last 5 MHz channel in the pass band.
9.2.5.1 Minimum Requirement
The power of any spurious emission shall not exceed:
Table 9.13: UTRA Repeater up-link and down-link spurious emissions limits for in geographic coverage area of PHS
Band |
Maximum Level |
Measurement Bandwidth |
Note |
1884,5 ‑ 1915,7 MHz |
-41 dBm |
300 kHz |
9.2.6 Co-existence with UTRA-TDD and/or E-UTRA TDD
9.2.6.1 Operation in the same geographic area
This requirement may be applied to geographic areas in which both UTRA-TDD and/or E-UTRA TDD and UTRA-FDD Repeaters are deployed.
9.2.6.1.1 Minimum Requirement
In the down-link direction of the Repeater the power of any spurious emission shall not exceed:
Table 9.14: UTRA Repeater down-link spurious emissions limits in geographic coverage area of UTRA-TDD and/or E-UTRA TDD
System type operating in the same geographical area |
Band for co-existence requirement |
Maximum Level |
Measurement Bandwidth |
Note |
UTRA TDD Band a) or |
1900 ‑ 1920 MHz |
-52 dBm |
1 MHz |
|
UTRA TDD Band a) or |
2010 ‑ 2025 MHz |
-52 dBm |
1 MHz |
|
UTRA TDD Band d) or |
2570 ‑ 2620 MHz |
-52 dBm |
1 MHz |
|
UTRA TDD Band f) or |
1880 – 1920 MHz |
-52 dBm |
1 MHz |
Applicable in China. |
UTRA TDD in Band e) |
2300 – 2400 MHz |
-52 dBm |
1 MHz |
|
E-UTRA Band 41 |
2496 – 2690 MHz |
-52 dBm |
1 MHz |
|
E-UTRA Band 42 |
3400 – 3600 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band XXII. |
E-UTRA Band 43 |
3600 – 3800 MHz |
-52 dBm |
1 MHz |
|
E-UTRA Band 44 |
703 – 803 MHz |
-52 dBm |
1 MHz |
|
NOTE 1: The co-existence requirements do not apply for the 10 MHz frequency range immediately outside the repeaters operating band (see Table 4.1). Emission limits for this excluded frequency range may be covered by local or regional requirements. NOTE 2: The table above assumes that two operating bands, where the frequency ranges would be overlapping, are not deployed in the same geographical area. For such a case of operation with overlapping frequency arrangements in the same geographical area, special co-existence requirements may apply that are not covered by the 3GPP specifications. |
In the up-link direction of the Repeater the power of any spurious emission shall not exceed:
Table 9.14A: UTRA Repeater up-link spurious emissions limits in geographic coverage area of UTRA-TDD and/or E-UTRA TDD
System type operating in the same geographical area |
Band for co-existence requirement |
Maximum Level |
Measurement Bandwidth |
Note |
UTRA TDD Band a) or |
1900 ‑ 1920 MHz |
-53 dBm |
100 kHz |
This requirement is applied only to UTRA FDD Repeater operating in band I, band II or band XXV. |
1900 ‑ 1920 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band I, band II or band XXV. |
|
UTRA TDD Band a) or |
2010 ‑ 2025 MHz |
-52 dBm |
1 MHz |
|
UTRA TDD Band d) or |
2570 ‑ 2620 MHz |
-53 dBm |
100 kHz |
This requirement is applied only to UTRA FDD Repeater operating in band VII. |
2570 ‑ 2620 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band VII. |
|
UTRA TDD Band f) or |
1880 – 1920 MHz |
-53 dBm |
100 kHz |
Applicable in China. This requirement is applied only to UTRA FDD Repeater operating in band II or band XXV. |
1880 – 1920 MHz |
-52 dBm |
1 MHz |
Applicable in China. This requirement does not apply to UTRA FDD Repeater operating in band II or band XXV. |
|
UTRA TDD in Band e) or |
2300 – 2400 MHz |
-52 dBm |
1 MHz |
|
E-UTRA Band 41 |
2496 – 2690 MHz |
-52 dBm |
1 MHz |
|
E-UTRA Band 42 |
3400 – 3600 MHz |
-52 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band XXII. |
E-UTRA Band 43 |
3600 – 3800 MHz |
-52 dBm |
1 MHz |
|
E-UTRA Band 44 |
703 – 803 MHz |
-52 dBm |
1 MHz |
|
NOTE 3: The co-existence requirements do not apply for the 10 MHz frequency range immediately outside the repeaters operating band (see Table 4.1). Emission limits for this excluded frequency range may be covered by local or regional requirements. NOTE 4: The table above assumes that two operating bands, where the frequency ranges would be overlapping, are not deployed in the same geographical area. For such a case of operation with overlapping frequency arrangements in the same geographical area, special co-existence requirements may apply that are not covered by the 3GPP specifications. |
NOTE 1: The requirements of -53dBm/100kHz in Table 9.14 and Table 9.14A, which are respectively for the down link and up link direction of the Repeater reflect what can be achieved with present state of the art technology and are based on a coupling loss of 73 dB between a Repeater and a UTRA TDD BS receiver.
NOTE 2: The requirements shall be reconsidered when the state of the art technology progresses.
9.2.6.2 Co-located Repeaters and UTRA-TDD and/or E-UTRA TDD base stations
This requirement may be applied for the protection of UTRA-TDD BS receivers when UTRA-TDD BS and UTRA-FDD Repeater are co-located.
9.2.6.2.1 Minimum Requirement
In the down-link direction of the Repeater the power of any spurious emission shall not exceed:
Table 9.15: UTRA Repeater down-link spurious emissions limits for protection of co-located UTRA TDD and/or E-UTRA TDD BS receiver
Type of co-located Base Station |
Band for co-location requirement |
Maximum Level |
Measurement Bandwidth |
Note |
UTRA TDD Band a) or |
1900 ‑ 1920 MHz |
-86 dBm |
1 MHz |
|
UTRA TDD Band a) or |
2010 ‑ 2025 MHz |
-86 dBm |
1 MHz |
|
UTRA TDD Band d) or |
2570 ‑ 2620 MHz |
-86 dBm |
1 MHz |
|
UTRA TDD Band f) or |
1880 – 1920MHz |
-86 dBm |
1 MHz |
Applicable in China |
UTRA TDD Band e) or |
2300 – 2400MHz |
-86 dBm |
1 MHz |
|
E-UTRA Band 41 |
2496 – 2690 MHz |
-86 dBm |
1 MHz |
This requirement does not apply to E-UTRA FDD Repeater operating in band VII. |
E-UTRA Band 42 |
3400 – 3600 MHz |
-86 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band XXII. |
E-UTRA Band 43 |
3600 – 3800 MHz |
-86 dBm |
1 MHz |
|
E-UTRA Band 44 |
703 – 803 MHz |
-86 dBm |
1 MHz |
|
NOTE 1: The co-location requirements do not apply for the 10 MHz frequency range immediately outside the repeaters operating band (see Table 4.1). Emission limits for this excluded frequency range may be covered by local or regional requirements. NOTE 2: The table above assumes that two operating bands, where the frequency ranges would be overlapping, are not deployed in the same geographical area. For such a case of operation with overlapping frequency arrangements in the same geographical area, special co-existence requirements may apply that are not covered by the 3GPP specifications. |
In the up-link direction of the Repeater the power of any spurious emission shall not exceed:
Table 9.15A: UTRA Repeater up-link spurious emissions limits for protection of co-located UTRA TDD and/or E-UTRA TDD BS receiver
Type of co-located Base Station |
Band for co-location requirement |
Maximum Level |
Measurement Bandwidth |
Note |
UTRA TDD Band a) or |
1900 ‑ 1920 MHz |
-53 dBm |
100 kHz |
This requirement is applied only to UTRA FDD Repeater operating in band I, band II or band XXV. |
1900 ‑ 1920 MHz |
-86 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band I, II or band XXV. |
|
UTRA TDD Band a) or |
2010 ‑ 2025 MHz |
-83 dBm |
100 kHz |
This requirement is applied only to UTRA FDD Repeater operating in band I. |
2010 ‑ 2025 MHz |
-86 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band I |
|
UTRA TDD Band d) or |
2570 ‑ 2620 MHz |
-53 dBm |
100 kHz |
This requirement is applied only to UTRA FDD Repeater operating in band VII. |
2570 ‑ 2620 MHz |
-86 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band VII. |
|
UTRA TDD Band f) or |
1880 – 1920 MHz |
-53 dBm |
100 kHz |
Applicable in China. This requirement is applied only to UTRA FDD Repeater operating in band II or band XXV. |
1880 – 1920 MHz |
-86 dBm |
1 MHz |
Applicable in China. This requirement does not apply to UTRA FDD Repeater operating in band II or band XXV. |
|
UTRA TDD in Band e) or |
2300 – 2400 MHz |
-86 dBm |
1 MHz |
|
E-UTRA Band 41 |
2496 – 2690 MHz |
-86 dBm |
1 MHz |
This requirement does not apply to E-UTRA FDD Repeater operating in band VII. |
E-UTRA Band 42 |
3400 – 3600 MHz |
-86 dBm |
1 MHz |
This requirement does not apply to UTRA FDD Repeater operating in band XXII. |
E-UTRA Band 43 |
3600 – 3800 MHz |
-86 dBm |
1 MHz |
|
E-UTRA Band 44 |
703 – 803 MHz |
-86 dBm |
1 MHz |
|
NOTE 4: The co-location requirements do not apply for the 10 MHz frequency range immediately outside the repeaters operating band (see Table 4.1). Emission limits for this excluded frequency range may be covered by local or regional requirements. NOTE 5: The table above assumes that two operating bands, where the frequency ranges would be overlapping, are not deployed in the same geographical area. For such a case of operation with overlapping frequency arrangements in the same geographical area, special co-location requirements may apply that are not covered by the 3GPP specifications. |
NOTE 1: The requirements of -53dBm/100kHz in Table 9.15 and Table 9.15A , which are respectively for the down link and up link direction of the Repeater reflect what can be achieved with present state of the art technology and are based on a coupling loss of 73 dB between a Repeater and a UTRA TDD BS receiver.
NOTE 2: The requirements of -83dBm/100kHz in Table 9.15A for the up link direction of the Repeater reflect what can be achieved with present state of the art technology and are based on a coupling loss of 43 dB between a Repeater and a UTRA TDD BS receiver.
NOTE 3: The requirements shall be reconsidered when the state of the art technology progresses.
9.2.7 Void
9.2.8 Protection of public safety operations
This requirement shall be applied to Repeater operating in Bands XIII and XIV to ensure that appropriate interference protection is provided to 700 MHz public safety operations. This requirement is also applicable at specified frequencies falling between 12.5 MHz below the first carrier frequency used and 12.5 MHz above the last carrier frequency used.
9.2.8.1 Minimum Requirement
The power of any spurious emission shall not exceed:
Table 9.16: Spurious emissions limits for the up-link and down-link of UTRA Repeater for protection of 700 MHz public safety operations
Operating Band |
Band |
Maximum Level |
Measurement Bandwidth |
Note |
XIII |
763 – 775 MHz |
-46 dBm |
6.25 kHz |
|
XIII |
793 – 805 MHz |
-46 dBm |
6.25 kHz |
|
XIV |
769 – 775 MHz |
-46 dBm |
6.25 kHz |
|
XIV |
799 – 805 MHz |
-46 dBm |
6.25 kHz |
This requirement shall be applied to repeaters operating in Band XXVI to ensure that appropriate interference protection is provided to 800 MHz public safety operations. This requirement is also applicable at specified frequencies falling between 12.5 MHz below the first carrier frequency used and 12.5 MHz above the last carrier frequency used.
The power of any spurious emission shall not exceed:
Table 6.16A: Spurious emissions limits for the up-link and down-link of UTRA Repeater for protection of 800 MHz public safety operations
Operating Band |
Band |
Maximum Level |
Measurement Bandwidth |
Note |
XXVI |
851 – 859 MHz |
-13 dBm |
100 kHz |
Applicable for offsets > 37.5kHz from the channel edge |